Show all posts by user
Printing issues ...
Page 1 of 1 Pages: 1
Results 1 — 17 of 17
Another issue to add,heated bed not heating....i set temperature to 60 and it went to 35 then start to coming down.....i started to disassemble all electronics tomorow i'll connect everything again....
by
drwatsont
-
Printing
QuoteSupermec
drwatsont,
what happens to the head, if using the controls on the printer, you tell it to "Home All". If the nozzle ends up just off the front left hand side of the bed then that is where your FIRMWARE thinks is X=0, Y=0, Z=0. The slicer then needs to be set to reflect that. If the nozzle ends up at the centre of the bed then you need to tell the slicer that is where the zero posit
by
drwatsont
-
Printing
After trying some bed alignment the issue come up, when i press x-axis home instead of going direct to home takes small stepps until arrives home, and again in pronterface when i press the red button to go to middle of the bed it goes other place in bed...i pressed the red button more then once and it went to diferent locations
by
drwatsont
-
Printing
Just connected the printer to check Supermec and MCcarman last post and it's when i find out that every thing is normal again, i did nothing...what do you think about this?
by
drwatsont
-
Printing
QuoteHedgehog
honestly, if this "jam" happens every single time then it should be a nozzle jam. do a cold pull if it is the case.
Nozzle jam?the filament comes out ok..
by
drwatsont
-
Printing
QuoteMCcarman
There are other methods but the simplest way to look at the Gcode is to. Hang on better go back a step.
After you have sliced your model and generated the Gcode save the file.
Then if using windows open notebook, (Start menu > programs >Accessories). In notebook select open file, then browse to the Gcode file, (change the view to all files or it wont be visible).
The Gcode fi
by
drwatsont
-
Printing
What do i have to look for in g-code and retraction?
by
drwatsont
-
Printing
Hi,check the 2 files attached is that it? the printer does a different noise when printing that error
by
drwatsont
-
Printing
Quoteo_lampe
Quotedrwatsont
yes o_lampe i had to put a washer to align everything....a very thin one...i was getting good printings until my printer started to print outside of the object area,why this happens?
Looks like the nozzle bumped in the part and skipped some steps. This can happen from over extrusion or blobs from oozing. Check your e-steps and retraction settings.
Where do i check fo
by
drwatsont
-
Printing
QuoteSupermec
First check the gcode file and see what the printer is being told to print. Let us know what you find.
How do i check g-code?i've printed lots of this 10mm cube as it is my printing test before i print bigger parts and i've done like other sucefull printings but this time the print went out of the object
by
drwatsont
-
Printing
yes o_lampe i had to put a washer to align everything....a very thin one...i was getting good printings until my printer started to print outside of the object area,why this happens?
by
drwatsont
-
Printing
i tighten the screw 1/4(+/-)of turn,i i got a good part
by
drwatsont
-
Printing
talk to soon, see photo 1 it stoped there, photo 2 is to show how is the filament..
by
drwatsont
-
Printing
i've lowered the throat and printed a 10mm cube and it's ok i'm printing the support for y-axis motor so it's ok....
by
drwatsont
-
Printing
i tried to loose some filament and does the same at somepoint the filament does not extrude(i have printed good parts without loosing the filament) the files attached are from my extruder and one from a part that i tried to print with loose filament unsucceful
by
drwatsont
-
Printing
Supermec---i'll try to print spool holders with bearings
Farnomat--i've ptinted very good parts,this is new printer new spool new everything
Thank you both for your time and help
by
drwatsont
-
Printing
Hi i'm printing with PLA at 200ยบ it prints a few layers ok but after that stops feeding the filament,before i start printing i try to extrude 10mm a few times and it goes ok.
files attached:error 1 and error 4 are 2 examples of the issue,also sendind an image of the filament support and extruder
by
drwatsont
-
Printing