Moin floflo, Deine Konstruktion des Rahmens sieht sehr gut aus, ich überlege gerade auch einen Eigenbau in ähnlicher Form zu verwirklichen. Auch ich habe dabei an Linearschienen und Kugelumlaufspindeln auf allen Achsen gedacht. Die normalen Riemen, die in allen Druckern verbaut sind, sind meines Erachtens, gerade wenn mit höheren Geschwindigkeiten gefahren werden soll nicht präzise genug ( Wievon JET-A1 - Projekte
Hello, ive now diconnect all Cable from the Alligator for Checking Wires and Soldeing. I did found some cold Soldering at the REPRAP Electronic Endstops, i soldered all Endstops new and tested them, they are all fine now. Also the Motors ive tested with an Resistormeter (1.5 Ohms each Pair and no shortage between all Cables), they are fine, too. At last i flashed the REPRAP Firmware dc42/1.09hvon JET-A1 - Controllers
Hello EljefedsecuIT, many Thanks for your Reply,i am since Friday on my Journey at Home with my Alligator and my Mendel. Since Friday i ve tryed most Firmwares they fit the Alligator. Witch Firmware do you actualy use ? With Repetierhost and Server i can connect via Ethernet and USB, but i am very confused about the Arduino IDE, because of copying Files to the IDE that make the flashing work. Ivon JET-A1 - Controllers
@ EljefedsecurIT Thanks for your fast Reply :-) I ve been parked my Mendel-Alligator Project for a Long time because of Time shortage. Now i started a Week ago, reading all that Stuff from 3d Artists , Repetier and so on. Quickly i figured out, that many Things have changed ! The Problem with the Raspi i worked around with buying an Raspi 2B with Repetier Server running, with him i get a stable cvon JET-A1 - Controllers
Hello Marco, i ve many Problems to install and running Repetier-Server in an Rasperry Pi 3 with Alligator. The Problem seems to be the Wireing from Rasberry to Alligator, i get no right Connection to the Alligator. Is it possible to give us an Guide from beginning to running Repetier-Server ? Since you Guide here, there are so many changes in Soft- and Hardware, so i think its time for a new Guivon JET-A1 - Controllers
Hello, today i try to connect my Alligator with an RepRap Discount Full Graphic Display 12864 with 2 * 10 Pin Connectors ( Red PCB, Blue Backlighted Display, Rotary Encoder with Push Button, Buzzer, SD-SLOT, Kill Switch, mostley sold in the Bay ) . I made a Map, you can see witch Pins should welded together: Alligator Pin 1 (+5,0 Volt) to Display EXP1 Pin 10 -----------------------------------von JET-A1 - Controllers
Hello, good News, I got the Repetier Firmware on the Alligator ... YES ... After many try and error I put the Arduiono 1.6.3 ZIP File ( no Admin install ) on my D: Drive and it works with both UART USB and MCU USB . I don't know whats the difference between the Arduino.exe and the Arduino.zip ?!?! Important is the following, USB MCU PORT gets his Driver from Arduino\Drivers\ and the UART USB POvon JET-A1 - Controllers
Hello, this Morning I try to install Repetier Firmware to the Alligator Board. This is what I did: -unistal Arduino -delete C:\Users\Administrator\AppData\Roaming\Arduino15 -restart Windows -login as Administrator (everytime) -install Arduino 1.6.3 -restart Windows -install SAM in Arduino Board Manager -restart Windows -copy Files from Alligator-Repetier-Firmware-work092\src ... Board.txt andvon JET-A1 - Controllers
Hello EljefedsecurIT , my Alligator Board Serial No is 0085 and i connected the MCU USB with 12Volt Power this Moning and it works. Windows takes the Alligator as a BOSSA PROGRAM. Greetingsvon JET-A1 - Controllers
Hello, this is , what i did : - uninstalled Arduino 1.6.3 - deleted Folder Arduino15 C:\Users\PELLE\AppData\Roaming\Arduino15 - Windows restart - install Arduino 1.6.3 - open Arduino, instal Board Manager SAM - close Arduino - open Arduino - copy Files from 3DArtists/Github/Repetier to C:\Users\PELLE\AppData\Roaming\Arduino15\packages\arduino\hardware\sam\1.6.3\Variants ( Alligator r1 and r2 avon JET-A1 - Controllers
Hello, This is helping me a lot ! And now ive the Problem. Arduino IDE normaly uses the AVRMK II Programmer and with this i tried to progam this. I try using the Ardiuno ISP Programmer now. OK, your Boards seem to act like my Board , so on, so fine :-) Next i try your Ideas and will Report... At the 3D Artists Github Page you have 2 Sites for the Alligator Drivers , witch one do you use ? Thervon JET-A1 - Controllers
Hi, the Dipswitch is toward the Processor. When i Power 12V and use the USB UART Nr8, Windows will see the Board. When i use the Native USB without 12V nothing happens , Windows dont see the Board. Dipswitch is toward Processor. Tomorrow i try a different Computer with USB 2.0 maybe thats the issue... In the past i used some Arduino Clone with different Driver , so i take a look on a fresh andvon JET-A1 - Controllers
Hello Mark O, yes i did all the things discribbled in the 3dArtists Github. And I also took the Github Version of the Repetier Firmware and i tried the Repetier 0.92 with the Configurator. everytime the same. Strange is , that the Board is not coming up with the MCU USB Port, how should i program it , when Windows is not taking the Board ? Greetingsvon JET-A1 - Controllers
Hello EljefedsecurIT, i just set up the Arduino 1.6.3 like you said on your Blog. When i connect my Alligator with the USB MCU Port, nothing happens, Windows is not tking the Alligator , no Looking for Driver , nothing. It seems, that the USB MCU Port is Dead ! When i put 12v and use the UART USB Port on Alligator , Windows is lokking for Driver and tkes the board as a HS 232 in Printer an Devicevon JET-A1 - Controllers
Hello, on Sunday i tried to instal Repetier for Alligator to my naked Board using only the Native USB and Arduino 1.6.3 without 12v Power with no effort ... i tought the native USB Port is only for Progamming, but not even Windows 7 didnt showed up the Alligator ??? I wrote a Mail to Marco and he told me to connect the Board with 12v and program with the UART USB Port. Ok i did what he told me avon JET-A1 - Controllers
Hello, this is helping me so much. Thanks for the fast Help Greetings from Germanyvon JET-A1 - Controllers
Hello Marco, ist a nice Picture you take from the Display Board, but can you specify the Pins on the Display Board ? Witch Cable with ID, on witch Solderpin ? For Example: Pin 1 on Alligator Board to Solderpin ... on the Displayboard, that would be much easier for me to identify the correct Wiring ! I don t have any idea where on the Diplay is +3,3v or +5,0v and so on. In Repetier Firmware Convon JET-A1 - Controllers
Hello, is it possible to connect a Smart Control Display 12864 for Ramps 1.4 to the Alligator Board ? And when ist possible, how and where do i connect it ? When ist not possible , witch Display can i connect to the Board ? Thanks for your Help Jet-A1von JET-A1 - Controllers