QuoteBobyni and what is your output voltage between the S and ground? I just did on the bread board and it gives me 0.694V when not triggered and when triggered with metal, 0V Mine is a normally closed sensor that gives off 4.84V when the sensor is not near metal, it sinks the the Z-min pin to 0.7V through the 680 ohm resistor when it is near metal. Only 1 lead is attached to the Z-min as shown iby gwc2795 - Prusa i3 and variants
QuoteBobyni Quotegwc2795 QuoteRobkadett oh i googled now i know, my P802M is not have auto leveling (sensor.) but for a while, i can upgrade my printer with auto leveling. I think it can be work if i make senzor wire to end stop switch. and after that i have just upgrade my firmware ? I have installed Inductive sensoers on 3 of my P802M printers. The sensors are working as Z endstops. I have noby gwc2795 - Prusa i3 and variants
QuoteAx Quoteejlane QuoteAx Quoterowdyjoe QuoteAx Quoterowdyjoe Ax Yeah, it's been 45 min. and it's just now reacing 105C. Previous high temp was about 85C with a piece of cardboard on top so, this is real progress. I replaced the 16 (?) gauge wire to the bed with 14 gauge copper stranded and insulated the back side of the bed with aprox. 1/8" cork. Wooohoooo ! Just checked and the bed tempby gwc2795 - Prusa i3 and variants
QuoteRobkadett oh i googled now i know, my P802M is not have auto leveling (sensor.) but for a while, i can upgrade my printer with auto leveling. I think it can be work if i make senzor wire to end stop switch. and after that i have just upgrade my firmware ? I have installed Inductive sensoers on 3 of my P802M printers. The sensors are working as Z endstops. I have not been able to get the G2by gwc2795 - Prusa i3 and variants
Quoteejlane But the reason why I'm here reading this thread is that I'm having a problem with my migbot. I bought the extended size build platform, but the back ~40mm of it is unreachable by my extruder. My first thought was that the rods for the y axis were too short, but I've been in touch with Gary McKinney and he says that my parts are the right size. (~380mm for the smooth rods and ~400mm foby gwc2795 - Prusa i3 and variants
Vo.92 has better auto bed leveling and has corrected other issues.by gwc2795 - Prusa i3 and variants
I have added V0.92 Repetier Firmware to theby gwc2795 - Prusa i3 and variants
Quoterowdyjoe QuoteAx Quoterowdyjoe QuoteAx Quoterowdyjoe Ax Yeah, it's been 45 min. and it's just now reacing 105C. Previous high temp was about 85C with a piece of cardboard on top so, this is real progress. I replaced the 16 (?) gauge wire to the bed with 14 gauge copper stranded and insulated the back side of the bed with aprox. 1/8" cork. Wooohoooo ! Just checked and the bed temp is noby gwc2795 - Prusa i3 and variants
QuoteWalles it work at beginning all fine, and 220v is correct for me Adjust the voltage higher on the power supply outputby gwc2795 - Prusa i3 and variants
QuoteWalles ok, got a new voltmeter and checked the outputs on the power supply. all have 4.12V Is the switch on the power supply set to 110V it comes set to 220Vby gwc2795 - Prusa i3 and variants
QuoteWalles hiho, iam just finished to asseble my pursa i3. works all fine at the beginning, but then nothing goes anymore. The LCD just light a bit up and when i turn off the power for a short sec i see version fimreware and so on screen. when i connect to repetier host it always says "brown out reset initialising". Just the question, am i right that brown out means that something is wrong witby gwc2795 - Prusa i3 and variants
I have identified the LCD supplied with the P802M. It is PiBot Display/Controller extension with 20x4 character display In Repetier Firmware use #define FEATURE_CONTROLLER 8by gwc2795 - Prusa i3 and variants
Quoteveaceonee Any idea why the LCD goes all fritzy during prints? Does it every time about 5 minutes into the print. Still prints ok. When it does it measure the 5V line to make sure you are not having a voltage drop.by gwc2795 - Prusa i3 and variants
still no identification of the lcd?by gwc2795 - Prusa i3 and variants
QuoteCrackinX Hey guys, I have been running into an issue and am hoping someone can help. I attached a picture, I'm getting gaps in my outer shell, I'm getting them with two different brands of filament, and can't seem to pinpoint the cause. The layers are stuck well, I can't pull anything apart, I've messed with retraction in both directions with no effect, raised extrusion width also with no efby gwc2795 - Prusa i3 and variants
Quoteworthidlj Hi Folks, I've had help from members before in setting up my printer (large bed version, MKS 1.3 Board) and I had it working for a while and made a few decent prints. However I had a go at configuring the step counts of the motors using the YACO print file and updated the configuration.h file and uploaded it through Arduino. Since then whenever I turned the printer on I could tuby gwc2795 - Prusa i3 and variants
Quoteveaceonee IDK..its weird, temps are diplaying, but I keep gettin a 104 TO error every time now. Can you measure the temperature of the hotend?by gwc2795 - Prusa i3 and variants
An adjustable Inductive sensor holder has been uploaded to the google drive. It is much easier to adjust the distance between the bed and the sensor. Print 1 each adj top and 1 each adj bottom file. Items needed: 1 each M3x50MM screw or equiv in SAE 1 each M6x40MM compression spring or equiv in SAEby gwc2795 - Prusa i3 and variants
Has anyone converted the P802M to run on Marlin?by gwc2795 - Prusa i3 and variants
Quoterowdyjoe QuoteAx Quoterowdyjoe Another issue ....I can't get the extruder nozzel at the correct height for printing. Last couple of attempts at printing the test cube failed because the nozzle dug into the tape on the bed. I had manually leveled the bed but, when it began printing the nozzle was too close to the bed. How do I fix this problem? I have a feeling I'm missing something in tby gwc2795 - Prusa i3 and variants
QuoteGoldendark Hello, thx for this thread your google drive is usefull I have bought a PL-05N captor to activate autolevelling. Do you have STL to mount It ? tuto : I put the P802M Sensor Mount in the This sensor holder is for the SN04 series inductive sensors, but should fit others. Gerryby gwc2795 - Prusa i3 and variants
No body can identify this 3D printer LCD and controller? I need to use it with marlin. I really need the help. Thanks Gerryby gwc2795 - Prusa i3 and variants
QuoteBratan I've been printing with PLA on heated bed covered by Kapton tape. It was printing great yesterday, when it was pretty chilly in my room (under 65F). Today it's 70F I can't get damn thing to print single thing without head dragging away first layer, it just doesn't stick... I re-leveled bed, using same settings as yesterday, nothing. Switched to ABS and it works fine. Does room temperby gwc2795 - Prusa i3 and variants
Quotebmark25116 0.91 doesn´t support using the 12864 full graphic display I think, because there are displays shown in USER INTERFACE ? But there is a lot of other trouble with repetier. Is it better to use Marlin and can I use the Repetierhost with it ? Bernd Yes you can use Repetier with Marlin. What is a 12864 display?by gwc2795 - Prusa i3 and variants
Quotebmark25116 I changed the settings with 0.92, 0.91 doesn`t work with me... Butit is not everything working... Bernd I can't get either one of them to work either.by gwc2795 - Prusa i3 and variants
Quotebmark25116 I will do my best, just now I have chaged the motherboards settings with the repetier configuration tool. Hoping that works... Bernd Wish I could help you more but the V0.91 Repetier Configuration tool will not download any configuration I make. V0.92 will not compile so I am having to convert to Marlin.by gwc2795 - Prusa i3 and variants
Quotebmark25116 Solved, I have got the download working. Thanks again. I will try to upload this to my new Ramps board... Bernd Good luck. let us knowby gwc2795 - Prusa i3 and variants
Quoterowdyjoe QuoteAx Quoterowdyjoe Ax Yeah, it's been 45 min. and it's just now reacing 105C. Previous high temp was about 85C with a piece of cardboard on top so, this is real progress. I replaced the 16 (?) gauge wire to the bed with 14 gauge copper stranded and insulated the back side of the bed with aprox. 1/8" cork. Wooohoooo ! Just checked and the bed temp is now at 107C. I forgot tby gwc2795 - Prusa i3 and variants
QuoteRRuser That's one of the standard reprap screens. Thanks for the reply RRuser. I did not specify that I need to know what the #DEFINE would be in marlin. The P802M uses Repetier v0.91 and the Repetier configurator. The v0.91 configurator does not run on IE, Chrome or Opera on my computer so I need to convert to marlin to add a Inductive sensor for bed leveling. It is strange about the v0.9by gwc2795 - Prusa i3 and variants
I have added the P802M Firmware, P802M Printed Parts and P802M Instructions on a Google Drive. Hope they help.by gwc2795 - Prusa i3 and variants