Is it possible do display the measurement result of each point during bed leveling on the LCD screen? Watching these values during bed leveling would give a good information about the alignment of the bed.by rvator - Firmware - Marlin
I have the issue with both USB (Repetier) and SD card printing. Can't reproduce the behavior with S3D but was unsatisfied with the slicing quality for this application (single wall 3DLabPrint Aircraft) In the meantime I adapted the S3D gcode which was prepaired from 3DLabPrint to my E3D-Bigbox and have good results.by rvator - Firmware - Marlin
The same microstep setting on the drivers for E0 & E1?by rvator - Firmware - Marlin
On my E3D-BigBox/Rumba with Marlin 1.1.x-bugfix I observed irregular bumps on the outer wall. Looking closer I realised, that at the position of the bumps a very short speed drop occurs which leads to a short over extrusion. Looking into the gcode (Cura 2.6.2) I found always some points located close together exactly at the position of the bumps. I edited the gcode by hand and removed the poinby rvator - Firmware - Marlin
Stimmt, mit AUTO_BED_LEVELING_BILINEAR sehe ich diese Ausreißer nicht mehr!by rvator - Software
Habe inzwischen weitere Tests mit Marlin-1.1.1 und ABL durchgeführt und neue Erkenntnisse: Die beschriebenen Probleme treten erst auf, wenn man mehr als 6 Messpunkte wählt. X x Y 2 x 2 geht 3 x 2 geht 2 x 3 geht 3 x 3 Fehler 2 x 4 Fehler 4 x 2 Fehler Gruß, Franzby rvator - Software
Hallo Siggi, danke, aber bei Gitub habe ich das Problem als "rv4" eingestellt. Aber darauf, dass ich nicht der Einzige bin hat mich ersthelfer mit seinen Versuchen gebracht. Übrigens, habe einen BLToch Sensor, hat also mit dem Bettmaterial nichts zu tun. Für mich sieht es wie ein Problem mit der Speicherverwaltung in der Firmware aus. Aber komisch finde ich es schon, dass man so wenig von andereby rvator - Software
Ob's genau genug wird ist noch eine andere Sache. Aber hier geht es um komische Ausreißer bei zwei von 9 Messwerten. Und immer die selben Punkte. Für mich sieht das nach einem Firmware Problem aus. Gruß, Franzby rvator - Software
Hallo AlterBastler, danke für die Antwort, aber ich habe mic zu früh gefreut! Die Ergebnisse mit Marlin-1.1.1: Marlin 1.1.1 10:59:25.753 : -0.07528 +0.01972 +0.03472 10:59:25.754 : +0.05472 +0.09222 -0.01028 10:59:25.758 : +12.13330 +0.00972 -0.11528 10:59:25.762 : X:289.00 Y:185.00 Z:7.67 E:0.00 Count X:46240 Y:33300 Z:3060 10:59:25.762 : ok 11:01:15.610 : (0,0) 11:01:15.613 : -0.09389 +0.by rvator - Software
Habe noch einige Test durchgeführt und so wie es aussieht bin ich auf einen Bug beim BedLeveling gestoßen. Wenn man sich die Meßwerte beim 3x3 Raster ansieht macht der erste Messpunkt vorne, links (dritte Zeile / erste Spalte) meist keinen Sinn. Auch das Beispiel oben, von ersthelfer zeigt so ein Verhalten: +1.95728 +1.28787 +0.38056 -0.00000 +0.05761 -0.94572 -24.10810 -1.19302 -2.33706 Wby rvator - Software
Kämpfe z. Zt. auch mit G29 AutoBedLeveling und Marlin-1.1.0-RC8 BugFix mit BLTouch Sensor. Ist der Düsenabstand nach G28 richtig eingestellt, so ist er anschließend nach G29 meist etwas größer. Viele Grüße, Franzby rvator - Software