Search results

Jump to: navigation, search

Create the page "%s" on this wiki! See also the search results found.

  • SpoolHead
    ...ining challenges for pure self-manufacture", he writes that, of the Reprap's own parts, the most difficult to self-manufacture would be "electronic comp ...to include wire elements in a printed part would greatly expand the Reprap's capability of self-manufacture, whilst allowing it to manufacture a wider v
    9 KB (1,361 words) - 20:28, 23 January 2013
  • Darwin/Patch
    ...Darwin builders might mistakenly drill them out too large, not knowing it's meant to be an [[interference fit]]. (This happened to the authors, which f
    2 KB (284 words) - 14:07, 22 November 2015
  • Community
    Q: ''Should this be in the wiki? I don't know if it's appropriate.''<br> ...run this site. Or why. Because we're very serious about that. And that's what this page is really for, is '''Policy'''. Because most people don't r
    3 KB (447 words) - 15:28, 30 December 2019
  • V
    A new approach to "Recycler!" See Prober's comments http://forums.reprap.org/read.php?171,34188
    461 bytes (66 words) - 06:22, 26 November 2011
  • Bluetooth Wireless Communication
    Sweet, that's all setup.
    6 KB (965 words) - 05:22, 30 December 2014
  • Heated Bed
    ===Blue Painter's Tape=== ...e painter's tape which leads to small rips and tears. As the blue painter's tape is cheap, easy to find, and easy to work with, it isn't a problem to r
    31 KB (5,100 words) - 21:49, 11 November 2018
  • Mendel/Files/edrawings
    Project Lead(s): Mr. Jagannathan
    4 KB (616 words) - 14:12, 2 November 2011
  • Trystan's Wooden Mendel
    Trystan's wooden Mendel RepRap plans are perhaps the best [[Development:Wooden Mendel
    884 bytes (115 words) - 12:36, 16 November 2010
  • Powder Printer
    Printing a full mendel using this process has it's drawbacks, the picture shows an X Carriage printed using plaster with a CA
    1 KB (220 words) - 05:42, 8 September 2013
  • Pirated CupCake
    ...s. The plastic and plywood parts were laser-cut with Roosevelt High School's laser cutter and free material from donation. The CupCakeStrap is different So, I bet you're asking "What's the attraction to building a Cupcake, with its smaller print area, high pri
    24 KB (3,862 words) - 23:34, 19 November 2013
  • Wade's Geared Extruder
    {{Languages|Wade's Geared Extruder}} [http://grabcad.com/library/wade-s-geared-extruder-onshape-cad-1 GrabCAD]
    10 KB (1,618 words) - 09:33, 5 November 2016
  • Making a Hobbed Bolt
    == Wade's original instructions == This is an earlier version with using threaded rod - it's harder to get the hobbing concentric when you cut it into the threads.
    6 KB (1,032 words) - 21:44, 5 February 2024
  • Arduino Mega Pololu Shield
    ...onics]]. Version 1.25 and earlier are "1.5 layer" designed boards (i.e. it's double sided board, but one of layers can easily be replaced with wire-jump ...ired by Vik's work with EasyDrivers. Circuit design based mostly on Adrian's [[Pololu_Electronics]]. Joaz at RepRapSource.com supplied initial pin defin
    21 KB (3,268 words) - 16:19, 20 November 2018
  • Mendel Troubleshooting
    The x axis needs to be level once it's sitting on the Z screws. If your machine is on a (near) level surface, plac ...do I move the extrude hole in RepRap host software? The software thinks it's on the right side and mine is on the left.''
    6 KB (967 words) - 23:16, 12 December 2014
  • Nichrome
    ...ood idea to use a recognized vendor to ensure you get the correct type. It's also possible to find Nichrome wire and insulation at local shops, typicall
    2 KB (239 words) - 17:49, 29 May 2013
  • Kapton Tape
    ...r />Kapton tape is well suited for fastening heating elements. As such, it's the material of choice for fastening heating wire to the heater barrel of a | [http://www.charlies3dtechnologies.com/ Charlie's 3D Technologies]
    6 KB (829 words) - 19:20, 18 July 2016
  • Endstop/fr
    Ces points de départ sont signalés par des interrupteurs (déclencheurs) que l'on appelle endstop ou '''limite ...la plus basique, constitués d'un interrupteur (switch) ordinaire reccordés par 2 fils. <br/>
    5 KB (776 words) - 06:03, 16 May 2015
  • House Style
    And it's a bit tricky. So I'm awake at 5:28 AM. Which means I'll ask you guys to sor Maybe it gets a 2D barcode, using whatever's most popular and works:
    3 KB (465 words) - 12:46, 14 July 2014
  • Community/6x10000s Problem
    No it's not. We can do it with clever scripting, lots of server space, and an "agi
    3 KB (471 words) - 09:10, 13 January 2015
  • High Temperature Metal Casting
    ...ory on the subject is [http://www.youtube.com/user/myfordboy#p/p myfordboy's videos]. ...version of [http://www.backyardmetalcasting.com/book_fp.html Lionel Oliver]s "''The flowerpot crucible furnace''"
    12 KB (1,854 words) - 08:17, 19 February 2013

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)

Retrieved from "https://reprap.org/wiki/Special:Search"