Search results

Create the page "Arduino pololu" on this wiki! See also the search results found.

• StepStick/ru
  :''Please note: StepStick has 0.2 ohm sense resistors instead of [[Pololu stepper driver board]]s 0.05 ohm. This limits the current to 1A. See [[Not [[Category:Pololu electronics]]
  15 KB (2,421 words) - 19:24, 24 February 2019
• StepStick/ua
  :''Please note: StepStick has 0.2 ohm sense resistors instead of [[Pololu stepper driver board]]s 0.05 ohm. This limits the current to 1A. See [[Not [[Category:Pololu electronics]]
  15 KB (2,421 words) - 19:25, 24 February 2019
• RAMPS 1.7/ua
  |description = RepRap Arduino Mega Pololu Shield Arduino MEGA based modular RepRap electronics.
  11 KB (1,668 words) - 09:10, 27 February 2019
• RAMPS 1.7 LCD
  |reprap = Pololu Electronics ...re in the EXP-2 port connector. This wire can be directly connected to the Arduino Reset pin or to D45, by setting jumper J2 on the LCD-03 board.
  3 KB (396 words) - 22:25, 5 March 2019
• RAMPS 1.4.4
  |description = RepRap Arduino Mega Pololu Shield Arduino MEGA based modular RepRap electronics.
  18 KB (3,072 words) - 05:13, 9 April 2022
• RAMPS 1.7 LCD/ru
  |reprap = Pololu Electronics ...re in the EXP-2 port connector. This wire can be directly connected to the Arduino Reset pin or to D45, by setting jumper J2 on the LCD-03 board.
  3 KB (326 words) - 09:27, 6 March 2019
• RAMPS 1.7 LCD/ua
  |reprap = Pololu Electronics ...re in the EXP-2 port connector. This wire can be directly connected to the Arduino Reset pin or to D45, by setting jumper J2 on the LCD-03 board.
  3 KB (396 words) - 22:28, 5 March 2019
• The incomplete RepRap Prusa Mendel beginner's guide/es
  ...en movimientos de motor. Hoy en día, las electrónicas más populares son Arduino con un escudo (shield) (o RAMPS, http://reprap.org/wiki/Ramps), una Sanguin ...pila, sube y almacena en al arduino vía el entorno de desarrollo (IDE) de Arduino.
  69 KB (11,487 words) - 14:54, 8 July 2019
• Automated Circuitry Making/ru
  ...2010 08050004.JPG | thumb | right | alt = Пример alt text | RepRap [[Pololu Electronics]] интерфейсная плата, фрезерованна ...к DIP ATmega328, используемые во многих платах Arduino, имеют шаг 2,54 мм (10 контактов / дюйм).
  40 KB (682 words) - 15:09, 31 July 2019
• Eagle Library/ru
  ...ата шагового двигателя Pololu]] и защита для Arduino Mega.
  1 KB (62 words) - 09:51, 2 August 2019
• Alternative Electronics/ru
  ....jpg|100px]] || [[Pololu_Electronics|Pololu]] || Adrianbowyer || GPL v2 || Arduino Mega || Yes || FiveD || Experimental/ DEFACTO || ...:Sinaptec|Sinaptec]] || GPL || || Yes || [[Teacup]] || ??? || Mount an [[Arduino Nano]] ATmega328P
  18 KB (2,604 words) - 08:58, 6 May 2020
• Alternative Electronics/ru/ua
  ....jpg|100px]] || [[Pololu_Electronics|Pololu]] || Adrianbowyer || GPL v2 || Arduino Mega || Yes || FiveD || Experimental/ DEFACTO || ...:Sinaptec|Sinaptec]] || GPL || || Yes || [[Teacup]] || ??? || Mount an [[Arduino Nano]] ATmega328P
  18 KB (2,604 words) - 08:59, 6 May 2020
• Alternative Electronics/ua
  ....jpg|100px]] || [[Pololu_Electronics|Pololu]] || Adrianbowyer || GPL v2 || Arduino Mega || Yes || FiveD || Experimental/ DEFACTO || ...:Sinaptec|Sinaptec]] || GPL || || Yes || [[Teacup]] || ??? || Mount an [[Arduino Nano]] ATmega328P
  18 KB (2,604 words) - 08:59, 6 May 2020
• Stepper motor/ru
  ...ar their peak torque with a current-limiting stepper controller (such as a Pololu A4988). ...of steppers, but remember that if you specify a low-resistance one and the Arduino controller has to chop the voltage to limit the current going through it, t
  16 KB (2,592 words) - 17:22, 11 September 2021

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)