Search results

Jump to: navigation, search
  • ...eformation of the object printer that mean a bad print.In fact AWARD -Anti Warping And Retraction Deformation- try to prevent this problem
    3 KB (474 words) - 08:52, 6 September 2012
  • ...della plastica che porta al distaccamento del pezzo dal piatto.AWARD-Anti Warping And Retraction Deformation-quindi cerca di prevenire questo tipo di proble
    3 KB (474 words) - 08:53, 6 September 2012
  • ...ily equipped with chamber that keeps the prints warm enough to prevent any warping.''' Working area is larger than in traditional RepRap, and is currently 210
    2 KB (290 words) - 10:33, 17 June 2016
  • ...ing to that surface after cooldown. Uneven moisture content is what CAUSES warping, so this is a bad idea.
    14 KB (2,171 words) - 08:32, 17 March 2016
  • ...traces. The PCB is 1/8” thick (2x that of the regular beds) to minimize warping and provide rigidity to allow mounting flexibility.
    2 KB (358 words) - 19:49, 9 November 2012
  • ...ing to that surface after cooldown. Uneven moisture content is what CAUSES warping, so this is a bad idea. ...r especially tall/thin parts, a heated build chamber can be used to reduce warping. If using an aluminum frame, you may want to [[Heated_bed#Thermal_Insulatio
    44 KB (6,727 words) - 11:30, 29 April 2020
  • ...e tabs can be easily removed and the holder can be printed without fear of warping.
    6 KB (1,122 words) - 05:21, 28 August 2018
  • <td>Your object experiences "warping"</td> <td>Your first print layer is thin, squished, or warping immediately.</td>
    14 KB (2,435 words) - 23:50, 26 February 2015
  • http://www.makerbot.com/blog/2011/06/23/12-ways-to-fight-warping-and-curling/
    11 KB (1,688 words) - 10:27, 5 June 2013
  • ...for the use of materials such as [[ABS]] which can experience significant warping if printing on a cold platform.
    2 KB (351 words) - 07:54, 30 November 2014
  • |problem01=Part warping and delamination as print progresses. ====Warping====
    29 KB (4,254 words) - 15:43, 14 March 2021
  • ...large cooling fan. It is used to cool the extruded plastic in case of its warping. Another smaller fan is used to cool down the y motor. ...large cooling fan. It is used to cool the extruded plastic in case of its warping. Another smaller fan is used to cool down the y motor. The only issue about
    10 KB (1,626 words) - 20:35, 9 December 2014
  • Warping can almost be considered as excluded
    1 KB (167 words) - 20:33, 27 December 2014
  • ...to do some LS work with just laser heating, it will be extremely prone to warping/curling/fouling etc. By doing most of the heating externally, you're also a
    16 KB (2,561 words) - 16:58, 23 May 2019
  • ...red water and oil as a warm printing bath for plastic printing to minimise warping, it covers some of the same concepts almost a year ago and refers to earlie
    5 KB (812 words) - 05:47, 15 May 2017
  • ...ded part from cooling (and shrinking) too quickly. Such shrinking leads to warping internal stresses in RP parts. The most common result is corners of parts l A technique used to prevent warping. Parts are built on top of a 'raft' of disposable material instead of direc
    11 KB (1,228 words) - 20:08, 22 May 2020
  • # not exhibit 'hourglass' warping, and
    18 KB (3,016 words) - 09:12, 29 July 2015
  • ...La contrazione dovuta al raffreddamento, infatti, accentua il fenomeno di warping (''vedere alla voce '''Deformazione''''') che deforma il pezzo stampato con
    5 KB (716 words) - 09:09, 15 July 2014
  • * Large objects suffer warping Also PLA suffer less ''warping'' and heatbed is not needed
    5 KB (791 words) - 07:38, 25 May 2016
  • ...ated bed, parts have a tendency to cool down too quickly. This results in warping of corners (as the plastic shrinks while cooling) or the part physically de
    25 KB (4,097 words) - 08:06, 21 May 2018

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)