Search results

Jump to: navigation, search

Page title matches

Page text matches

  • ...hermoplastExtruder_2_0#Electronics|Electronics Section]] above. The small stripboard circuit you see here is identical to one channel of the standard PWM Driver
    38 KB (6,703 words) - 17:54, 13 October 2013
  • |name = Stripboard Comms Controller |description = Stripboard Comms Controller
    12 KB (1,987 words) - 05:01, 25 July 2015
  • #REDIRECT [[Building A Stripboard Comms Controller]]
    52 bytes (6 words) - 05:01, 25 July 2015
  • ====Stripboard Designer 1.0==== ...ators.com/New%20Front%20Page/Documentation/Tools/Stripboard%20designer.htm Stripboard Designer 1.0]
    27 KB (4,082 words) - 01:36, 30 August 2019
  • ...MAX6675.pdf MAX6675]] chip, and is easily put together on a small piece of stripboard that plugs into the I2C connector on the extruder controller board. [[Image:stripboard-top.jpg|400px]] [[Image:stripboard-bottom.jpg|400px]]
    5 KB (848 words) - 08:13, 27 November 2011
  • ...holes. The end of the connector should be just flush with the edge of the stripboard.<br clear="all">[[Image:Usb-pcb-connections.jpg]][[Image:Usb-wire.jpg]] ...on the left view. Use a thin cable tie to attach the ribbon cable to the stripboard via the smaller holes. Leave a small loop free to give strain relief. Jum
    5 KB (920 words) - 10:17, 30 December 2014
  • | stripboard||1||1||Electronics A neat way to make the electrical connections is to cut a piece of stripboard the same width as the top of the reprapped part of the extruder. Put two 4
    11 KB (1,944 words) - 06:23, 18 March 2014
  • ==Stripboard PCB as a heating Element==
    31 KB (5,100 words) - 21:49, 11 November 2018
  • #REDIRECT [[Building A Stripboard Comms Controller]]
    52 bytes (6 words) - 05:02, 25 July 2015
  • ...a solderless breadboard or an off-the-shelf prototyping board (perfboard, stripboard, etc), or
    11 KB (1,564 words) - 14:24, 15 January 2015
  • ...that it is also quite straightforward to make it on a couple of pieces of stripboard. That is how I prototyped it, and that is described below as well. == Making the electronics using stripboard ==
    20 KB (3,300 words) - 09:47, 28 May 2014
  • = HOWTO: Building a stripboard Extruder Controller = * A piece of stripboard with 2.54mm (0.1") spaced continuous track.
    8 KB (1,325 words) - 20:07, 26 November 2011
  • File:BuildingAStripboardExtruderController-ExtruderStripboardTop SN754410.png
    Extruder stripboard layout, component side.
    (800 × 1,135 (313 KB)) - 06:31, 17 March 2010
  • File:BuildingAStripboardExtruderController-ExtruderStripboardTop SN754410.svg
    Source for extruder stripboard layout
    (524 × 744 (495 KB)) - 06:31, 17 March 2010
  • = HOWTO: Building A Stripboard Stepper Controller (for a Unipolar Motor) = * A piece of stripboard with 2.54mm (0.1") spaced continuous track. It should be a minimum of 23 h
    7 KB (1,090 words) - 06:34, 29 November 2014
  • #REDIRECT [[Building A Stripboard Stepper Controller]]
    54 bytes (6 words) - 22:57, 20 February 2014
  • File:BuildingAStripboardStepperController-StepperStripboardUnder.gif
    Underside of stripboard
    (535 × 316 (18 KB)) - 06:32, 17 March 2010
  • # Move motors and electronics (still on stripboard) onto the new RepRap frame. ...tely functional RepRap, though it is not a true RepRap because it has some stripboard controllers and so on. The final step is to produce a new RepRap using the
    1 KB (240 words) - 14:32, 6 December 2011
  • ...the ZD1901 opto interrupter prevalent in the Southern Hemisphere, a simple stripboard assembly is required. Details [[DarwinZD1901Opto|here]].
    7 KB (1,036 words) - 15:24, 23 July 2015
  • If all this checks out and you have verified the stripboard soldering, then you can apply power to the board. If you have a multimeter This is based on the older, [[BuildingAStripboardCommsController|stripboard comms controller]] designed by Simon.
    16 KB (2,457 words) - 09:39, 26 November 2011

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)