Search results

Create the page "$1" on this wiki! See also the search results found.

• Gear design
  ...etween teeth is notionally along a point just over half way (typically a 1:1.25 split) up the teeth, and this is called the 'Pitch Line'. The bit above ...st Common Divisor (GCD) of each gear tooth count equals 1. e.g. GCD(16,25)=1
  12 KB (2,042 words) - 21:54, 26 October 2015
• GearMotorStepper
  ...achieved so far appears to be about 7.5 degrees. For a threaded rod with a 1 mm pitch that gives us a resolution of 0.021 mm.
  2 KB (396 words) - 12:49, 30 April 2014
• GearedBoxForGM3Motor
  ...deatils a design to gear the Solarbotics GM3 motor down by approximately 3:1.
  246 bytes (34 words) - 05:07, 17 December 2011
• Generation 1 Electronics
  = Generation 1 Electronics = [[Category:Generation 1 electronics| ]]
  4 KB (659 words) - 15:27, 23 July 2015
• Generation 1 firmware
  [[Category:Generation 1 firmware| ]]
  868 bytes (109 words) - 15:18, 28 August 2015
• Generation 2 Electronics
  ...google.com/p/sanguino/downloads/detail?name=reprap_motherboard-electronics-1.0.zip&can=2&q= Sanguino RepRap Motherboard] that makes the connections easi === DC Motor Driver v1.1 ===
  14 KB (2,223 words) - 09:27, 26 November 2011
• Generation 2 firmware
  ...> there is a line that says <tt>#define EXTRUDER_COUNT 1</tt>. Change the 1 to 2 if you have two extruders. ...f the number of steps of the stepper motors that your RepRap does to cover 1 mm. Change these if need be. If you are not sure exactly what the gearing
  16 KB (2,592 words) - 06:53, 18 July 2015
• Generation 3 Electronics
  * 1 [[Motherboard_1_2|RepRap Motherboard]] (''mendel/electronics/motherboard'') * 1 [[Mendel USB and power connector]] (no Eagle design - it's a simple piece o
  10 KB (1,606 words) - 20:53, 19 February 2012
• Glossary
  * Plastic material made into (often 3 mm or 1.75mm) string to be used as raw material in 3D printers. * Extruded plastic (often < 1 mm).
  17 KB (2,735 words) - 22:34, 1 May 2024
• PSMD Triple Axis Stepper Driver
  ...laining the settings. The options are Full-stepping, 1/2, 1/4, 1/8th , and 1/16th microstepping.<br/>
  4 KB (586 words) - 05:56, 29 November 2014
• Gputils
  ...ls for the Microchip (TM) PIC microcontrollers. The version marked 0.13.4-1 in the Ubuntu and Debian repositories seem to share a common flaw, so we've ...rce package with <tt>wajig source gputils</tt>, fetching the latest 0.13.4-1 files from the gputils repository on SourceForge with
  968 bytes (146 words) - 18:38, 26 November 2011
• Half-roundWasherBearing
  ==== 1. Summary ==== ...me workshops. Fortunately, a servicable alternative can be made from M3 or 1/8 inch washers.
  3 KB (434 words) - 05:08, 17 December 2011
• HandmadeGears
  ...gnment holes. Remove the clamp and bolt. Mark the sheets from the top down 1,2,3 & 4 with an indellible marker, as in the image on the right (note: some Using an 8mm drill bit drill out the centre holes on sheets 1 & 4. This will allow an M8 bolt or section of rod to go through the mould,
  4 KB (722 words) - 17:03, 28 November 2011
• HighTemperatureMaterials
  After 3 1/2hrs, the stuff still isn't set. This batch is much slower for no obvious r ...r 10c a piece...) to allow it to be threaded onto the heater barrel. After 1/2hr the plaster was shaped with a rasp to remove unwanted protrusions.
  10 KB (1,794 words) - 19:25, 26 November 2011
• HintsForUsingTheStratasysDimensionRPMachine
  1) The download for the full 30-page manual which will walk you through the c ==== 1. MANUAL DOWNLOAD ====
  6 KB (786 words) - 17:11, 28 November 2011
• HyperbolicSpeed
  For example, a speed value of 255 will wait for a period of 256 - 255 = 1 time unit between each step or pulse. ...at a speed of 255 is twice as fast as a speed of 254. A PIC speed of 0 is 1/256th as fast as 255.
  3 KB (525 words) - 06:36, 11 January 2015
• IOBox
  * 1: Set outputs {| border="1"
  1 KB (187 words) - 17:17, 28 November 2011
• PIC in-circuit programming
  [[Category:Generation 1 electronics]]
  3 KB (495 words) - 15:28, 23 July 2015
• InterchangeableNozzleMk2
  ...drill bit. Drill your nozzle's hole into the bottom of this hole, going in 1.5mm-2mm. As the drill bit does not emerge from the other side of the rod ye Screw the rod into that M6 nut about 1/3 the way down it leaving the little hole and untidy sawn-off end pointing
  6 KB (996 words) - 17:24, 28 November 2011
• InvoluteProfile1
  Suppose that you want to design a 3:1 ratio gear pair. Using the 3:1 proportion you then need to apply that proportion to deciding the radii of ...Distance''' measure gives the thickness of the gear. The default value is 1 mm. Set it to 10 mm for this example. '''Again don't try to do anything u
  6 KB (960 words) - 08:01, 2 January 2015

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)