Welcome! Log In Create A New Profile

Advanced

Controllers

Anything related to printer controllers not being Duet, RAMPS or Sanguinololu: microprocessors, motor and heater driver circuitry, gEDA/KiCAD issues, soldering tips, etc. 
Subject Views Posts Last Post

Gen 3 wiring questions

by JNOD
771 3 06/05/2012 09:11PM
Last Post by Andrew Smith

UCN 5804 for stepper motor ?

by PeterArt
1,314 2 06/05/2012 08:14AM
Last Post by Traumflug

Stepper motor jumping back steps

by DJJonosound
1,337 2 06/03/2012 05:03PM
Last Post by Traumflug

Help with bootloader (Gen6 + others) - Need a numpies guide spinning smiley sticking its tongue out

by JNOD
1,141 5 06/03/2012 04:59PM
Last Post by Traumflug

temperature readings Gen7

by waste
705 2 06/03/2012 04:00PM
Last Post by nophead

Gen 3 Motherboard v1.2 capacitor C6 value?

by JNOD
671 1 06/02/2012 03:26PM
Last Post by JNOD

Sunbeam - AT90USB electronic

by codec
2,250 3 05/31/2012 09:47AM
Last Post by codec

Resistor Based Heated bed- Help needed

by cloud1771
707 3 05/29/2012 04:01PM
Last Post by cloud1771

xbee with arduino or wireless comm

by krish1043
939 2 05/28/2012 10:55AM
Last Post by BoriSpider

v2.1 Opto endstops salvage....is it possible?

by RepRapRaj83
1,346 6 05/25/2012 11:15AM
Last Post by RepRapRaj83

Pic18f4550

by PeterArt
1,893 6 05/23/2012 05:36AM
Last Post by Traumflug

(SOLVED) New wolfstrap with gen 6 and problems

by rotinaj13
1,376 6 05/20/2012 10:19PM
Last Post by rotinaj13

Ramps with arduino AND parallelport?

by thetenter
4,142 18 05/20/2012 07:11PM
Last Post by Fiddler

Techzone Monotronics, replacing ethernet cable to tip

by Yvan
576 1 05/20/2012 01:11PM
Last Post by Yvan

Problem with temperature levelling at around 125 degrees

by dustynus
751 6 05/20/2012 12:38PM
Last Post by Traumflug

LED orientation on mark 2 heated bed?

by 3D2B
845 2 05/20/2012 05:31AM
Last Post by Traumflug

Opto End Stop Broken

by nottheonlychris
1,075 7 05/19/2012 09:00AM
Last Post by Traumflug

Gen 6 board, no extruder movement

by Fractal
1,623 18 05/17/2012 07:02PM
Last Post by Fractal

gen6, extruder slow, mm and rate way off?

by dustynus
802 4 05/15/2012 11:21AM
Last Post by dustynus

Gen6 working but no Temp registering Attachments

by cmolle9790
1,408 9 05/14/2012 01:29PM
Last Post by cmolle9790

Motors stutter, no movement

by 13asilis
1,611 8 05/12/2012 04:59AM
Last Post by 13asilis

I´d like to do myself a PCB for a printer 3D RepRap. I need guidance please.

by pigmalion
1,071 5 05/01/2012 06:47PM
Last Post by crazy8

step stick current draw

by Barry_Scott
959 3 04/29/2012 04:28PM
Last Post by Barry_Scott

Need Look-up Table for Fluke 80PK-1

by ajames
777 2 04/18/2012 10:23PM
Last Post by CdnReprap

1284p Bootloader

by Legot
2,612 5 04/15/2012 02:07PM
Last Post by Korman

24v to 12v dc power regulator/convertor

by foshon
1,399 4 04/12/2012 03:28AM
Last Post by NewPerfection

Gen6 power supply. ATX alternative?

by Kikinaak
1,118 2 04/11/2012 04:16AM
Last Post by droftarts

CP210x-based USB-TTL converter for Gen7 electronics

by dslc
3,746 29 04/09/2012 12:59AM
Last Post by kittu

SDSS ????

by Sublime
3,507 6 04/07/2012 06:34PM
Last Post by nophead

R2C2 cost of importing to USA

by Media Conversions
1,176 5 04/04/2012 11:54PM
Last Post by brick_man