Welcome! Log In Create A New Profile

Advanced

Controllers

Anything related to printer controllers not being Duet, RAMPS or Sanguinololu: microprocessors, motor and heater driver circuitry, gEDA/KiCAD issues, soldering tips, etc. 
Subject Views Posts Last Post

Two Extruders - what electronic and soft?

by codec
733 1 02/21/2012 01:29AM
Last Post by codec

FaceShield Marlin Control Board

by technowizard12
790 1 02/17/2012 09:50PM
Last Post by technowizard12

Printrboard Firmware

by kang9468
1,313 4 02/15/2012 09:09PM
Last Post by lincomatic2

what electronics should i use?

by thegeekguy
2,711 9 02/08/2012 04:50AM
Last Post by Traumflug

I2C Testing Procedures

by Sal
2,679 6 02/03/2012 08:44AM
Last Post by Sacha

Raspberry

by Emmanuel
1,417 9 02/03/2012 04:57AM
Last Post by JoeDaStudd

open source ecology Universal Axis Controller

by Autarkyboy
665 1 01/22/2012 11:01AM
Last Post by Autarkyboy

Help with Software/Firmware for mixed motor types

by GlassPineapple
716 1 01/19/2012 04:10PM
Last Post by GlassPineapple

atx power adapter

by dissidence
713 1 01/18/2012 06:31PM
Last Post by dissidence

Arduino KiCad

by Willow Schlanger
3,393 4 01/14/2012 12:23PM
Last Post by Tom

Gen3 V1.2 Motherboard issue.

by liam.mcquellin
774 3 01/10/2012 08:30AM
Last Post by NoobMan

Need help programning the Extruder controller v2.2 board

by sirbj
937 3 01/09/2012 01:43PM
Last Post by sirbj

Weird problems with Techzone electronics

by jsadusk
1,381 6 01/07/2012 03:19PM
Last Post by Atomhax

food for thought (s) about getting away from the pololu

by terramir
1,139 8 01/07/2012 05:18AM
Last Post by Traumflug

SD Card > PIC24 code Attachments

by tofletcher
7,016 9 01/05/2012 05:15AM
Last Post by jitender

Generation 6 / other electronics questions

by slang800
1,751 15 12/31/2011 06:29AM
Last Post by geoffd

PCB Provided

by solo
904 1 12/21/2011 02:05AM
Last Post by solo

New Opto Endstop

by joaz
1,367 3 12/21/2011 02:01AM
Last Post by solo

New RepRap PCBs posted on the Wiki

by BodgeIt
1,380 3 12/20/2011 04:36AM
Last Post by solo

Calibrating for thermistor and other questions...

by billmi
986 2 12/17/2011 03:44PM
Last Post by billmi

Newbie Arduino questions

by scanboy
1,151 6 12/16/2011 06:06AM
Last Post by Traumflug

Residual engine noise axis X and Y

by turkka
1,104 4 12/15/2011 06:33PM
Last Post by bryanandaimee

Almost there, electrionics holding me up a bit though

by twelvexii
935 5 12/15/2011 11:48AM
Last Post by bryanandaimee

uploading problem with atmega644p and gen7 1.3.1

by turkka
1,018 3 12/15/2011 03:27AM
Last Post by turkka

Burning out StepSticks sad smiley Attachments

by epoxi
815 1 12/14/2011 12:14AM
Last Post by epoxi

Brushless DC Motors (BLDC)

by aka47
6,067 25 12/10/2011 07:58PM
Last Post by Chris (MN)

Azteeg X3 3DP Controller - Single board RAMPS Attachments

by royco
2,750 16 12/09/2011 04:09PM
Last Post by ravix

I Need to Add a Dummy Load to a Generator Output

by jacketfan
968 1 12/07/2011 08:25PM
Last Post by jacketfan

Stepstick with 2A steppers

by fest
2,140 6 12/06/2011 03:52PM
Last Post by fest

Stepper Driver 1.2 (Single Sided) Attachments

by Khan
2,395 27 12/05/2011 05:26AM
Last Post by Traumflug