Subject		Views	Posts	Last Post
	First layer full of bumps by Korri	19,193	6	07/29/2014 07:14PM Last Post by Opus
	Z axis wont move down by Soundtrackzz	720	4	07/29/2014 01:04PM Last Post by jbernardis
	Filament Change Tips by cobrageek	1,424	7	07/29/2014 08:11AM Last Post by kimented_
	Help!!! can't print by Mormonguy	465	9	07/28/2014 06:16PM Last Post by calad
	Thermal Compounds for Cartridge Heater by chuttney1	384	1	07/28/2014 01:25PM Last Post by chuttney1
	Z axis is inconsistent and the motors also move with Y axis by aeroalex	1,570	3	07/28/2014 11:30AM Last Post by BackEMF
	No Infill For Small Objects by MaFraL	845	9	07/28/2014 01:24AM Last Post by bbowden
	Not extruding enough filament by Kristina	462	3	07/28/2014 12:21AM Last Post by dexterousfolder
	Top layer has holes by AjaxOfTheRockies	947	4	07/26/2014 09:03PM Last Post by AjaxOfTheRockies
	extuding materal stops flowing by tobig11	374	7	07/26/2014 04:13PM Last Post by cdreid9999
	x axis shift unsolvable by soaring eagle	590	7	07/26/2014 02:02PM Last Post by cdreid9999
	Cura doesn't print the last part of the top layer? (Doesn't generate printing moves) by Ohmarinus	3,585	17	07/25/2014 08:42PM Last Post by happygoluckyaussie
	Calibrating acceleration and jerk by TopherMan	29,872	7	07/25/2014 03:37AM Last Post by Simonice
	Extruder Motor not turning while printing, but works while testing by Coldstone	4,293	17	07/25/2014 02:30AM Last Post by brucehvn
	Challenge: Finding "Echo in letters" problem. by Danitegue	565	3	07/25/2014 12:46AM Last Post by A2
	right side z motor stalls by dafeesh	2,252	10	07/24/2014 10:09PM Last Post by dafeesh
	Non uniform extrusion by dolphinboy	912	13	07/24/2014 09:45PM Last Post by ekaggrat
	Very Bad Warping by Zulfe	454	3	07/24/2014 05:27PM Last Post by 3dkarma
	Filament stripping and folding by epicepee	658	1	07/24/2014 04:56PM Last Post by epicepee
	New printer - Prints are printing small (Not scale settings) - Firmware? by reddragon	883	2	07/23/2014 06:53PM Last Post by 3dkarma
	Crooked Z, What else should I try? by MoonTimber	507	4	07/23/2014 03:21PM Last Post by MoonTimber
	ramps max6675 pin problem by DreamALike35	552	4	07/23/2014 10:09AM Last Post by DreamALike35
	Stepper motor will turn after multiple button pressings by domtropen	466	3	07/23/2014 09:50AM Last Post by domtropen
	Extruder heating to 210 then dropping below 25 degrees by Big3D	513	4	07/22/2014 04:54PM Last Post by pepe.squadrone
	Printed Mendel parts to high by Mendel90	467	7	07/22/2014 04:11PM Last Post by Mendel90
	Arduino over heating..still! by cool2print	591	4	07/22/2014 09:54AM Last Post by cool2print
	High temperature PLA? by astfgl	520	3	07/21/2014 09:22PM Last Post by Ralph.Hilton
	Cannot print solid layer over an infill layer by andytxc	582	5	07/21/2014 05:31PM Last Post by 3dkarma
	Funky prints with PLA vs ABS by scottdky	443	2	07/21/2014 11:29AM Last Post by MrDoctorDIV
	Computer can't find printer by mccajoe	416	4	07/20/2014 06:46PM Last Post by waitaki