Subject		Views	Posts	Last Post
	Printing Nylon - no cardboard - very good adherence by PulsedMedia	2,267	4	07/20/2014 04:22PM Last Post by to-the-nth
	How to relax tightly-wound ABS? by QuackingPlums	450	1	07/20/2014 01:52PM Last Post by QuackingPlums
	Stepper not work properly by tobig11	408	1	07/20/2014 12:02PM Last Post by tobig11
	firmware can choose the resolution, by Velocity	318	2	07/20/2014 10:49AM Last Post by brucehvn
	Effects of temp on ABS? by MrDoctorDIV	497	4	07/20/2014 10:42AM Last Post by brucehvn
	Z Wobble by mokash770	567	1	07/20/2014 05:19AM Last Post by mokash770
	How do I stop ABS sticking to the nozzle? by Dreadnaught426	438	2	07/19/2014 11:38PM Last Post by waitaki
	Prime settings maybe? by Floyd	339	1	07/19/2014 03:57PM Last Post by Floyd
	More jamming at end of spool by gmh39	419	3	07/19/2014 02:25AM Last Post by tmorris9
	Better print resolution/quality by createanddesign	841	5	07/18/2014 04:35PM Last Post by Ralf
	Steppers turn for a while but then vibrate by surfacelane	1,979	5	07/18/2014 11:52AM Last Post by surfacelane
	extruder skipping with PLA by ansiomatic	1,336	12	07/17/2014 10:23PM Last Post by MrDoctorDIV
	Extruder Gear Producing Clicking Noise by Zulfe	603	3	07/17/2014 04:57PM Last Post by Zulfe
	Difficulties while homing Z by borupdk	457	6	07/17/2014 04:56PM Last Post by borupdk
	Fan sometimes doesn't turn on by Setesh	301	2	07/17/2014 03:01PM Last Post by diytechshop
	Motors don't rotate by bhoke	457	3	07/17/2014 04:02AM Last Post by bhoke
	Weak Filament by Zulfe	537	2	07/17/2014 02:06AM Last Post by waitaki
	extruder stepper problem. by Rooski	460	7	07/16/2014 11:04PM Last Post by Rooski
	MakerFarm Prusa i3v Extruder Not Feeding Properly by Zulfe	1,767	2	07/15/2014 06:42PM Last Post by 3dkarma
	Excessive globbing at corner by Razorconcepts	648	3	07/15/2014 12:21AM Last Post by Razorconcepts
	Is there a minimum axis speed to achieve decent quality prints? by Mechanical Menace	341	2	07/14/2014 07:05PM Last Post by Opus
	MendelMax 1.5+ prints off the bed by mattwold42	411	5	07/14/2014 05:38PM Last Post by manton
	Print Quality Prusa I3 by Grazza	1,034	6	07/14/2014 08:29AM Last Post by Grazza
	hot end sometimes scrapes by mrkaras	879	14	07/13/2014 01:44PM Last Post by roady001
	Does Z wobble depend also on the material? by drmaestro	368	1	07/13/2014 01:08PM Last Post by drmaestro
	first couple of layers by t0bb	669	4	07/13/2014 12:23PM Last Post by swirvbox
	Brittle PLA prints by Capinho	1,242	7	07/12/2014 08:04PM Last Post by Capinho
	Constant clog issues by erreib	2,689	12	07/12/2014 07:12PM Last Post by cdreid9999
	Rafting and support not being generated as desired in Sli3er by BlenderGuy	874	8	07/12/2014 07:08PM Last Post by cdreid9999
	Removing saran wrap from abs?? (wrong section maybe) by cdreid9999	589	4	07/12/2014 07:03PM Last Post by cdreid9999