Subject		Views	Posts	Last Post
	Printer "freezes" on long prints by iron_dinges	5,367	18	11/27/2015 03:30AM Last Post by danielchow
	HIC Prusa i3 Stops Extruding Mid-print by iasjdhgpfiu	839	5	11/27/2015 03:22AM Last Post by imqqmi
	waves at one side on object by microspace	632	4	11/27/2015 01:35AM Last Post by microspace
	Won't start after heating. by hernyv92	1,533	9	11/26/2015 04:43PM Last Post by imqqmi
	BAD PRINTS in PRUSA i3 HEPHESTOS by nunoncunha	793	3	11/26/2015 12:19PM Last Post by nunoncunha
	PETG extrusion issues by drm	1,020	5	11/26/2015 05:14AM Last Post by o_lampe
	Prusa I3 skipping steps later on in my prints by drud1995	673	4	11/25/2015 11:44PM Last Post by RRuser
	full graphic smart LCD issue by MazingHaoh	528	3	11/25/2015 02:16PM Last Post by balbers
	Support Material How-To by perseveranze	442	1	11/25/2015 12:20AM Last Post by perseveranze
	Prusa i3 xl extruder warmt niet op na slicen in repetier by chagoii	685	9	11/24/2015 05:09PM Last Post by imqqmi
	Slic3r Print Settings - Where's the guide? by prispin	491	5	11/23/2015 11:04AM Last Post by prispin
	Infill doesn't support top layers by alnaufra	642	6	11/22/2015 06:21AM Last Post by RRuser
	Weak infill by matys292	1,924	15	11/22/2015 05:53AM Last Post by RRuser
	Aldi craft glue... by Downunder35m	2,290	6	11/22/2015 02:51AM Last Post by Downunder35m
	Lazy printer by T3D	449	1	11/21/2015 06:02PM Last Post by T3D
	I'm new to PLA. Please help me out here... by the_digital_dentist	717	14	11/21/2015 01:50PM Last Post by the_digital_dentist
	Strange liquid from extruder by Lazerlord	508	2	11/20/2015 10:07PM Last Post by Downunder35m
	Extruder not feeding by ame	459	6	11/20/2015 05:08PM Last Post by ame
	Y-Axis is fine and then offsets several layers and then is fine again. by TyCobb	570	13	11/20/2015 12:22PM Last Post by TyCobb
	Servo Deployment Causes Brown Out by jwgv23	580	5	11/20/2015 10:45AM Last Post by jwgv23
	Hot end rubbing over print by Mtheuma	681	6	11/20/2015 10:22AM Last Post by tjnamtiw
	deformazione oggetto by Dominikx	343	3	11/20/2015 05:21AM Last Post by Alticcio
	test cube 17,5mm instead of 20mm by Alticcio	545	19	11/20/2015 04:03AM Last Post by Alticcio
	G29 doesnt correct level. by nesthaesis	439	2	11/18/2015 04:28AM Last Post by imqqmi
	Layer shifts after 60 minutes of printing, please help! by Rolleros	948	12	11/17/2015 06:49PM Last Post by Downunder35m
	Heated Bed PCB Heatbed MK1 not reaching 80 degrees by danrmount	1,355	2	11/17/2015 05:10PM Last Post by imqqmi
	Universal 3D printing filament spool standard 2014   (Pages: 1 2 3 4) by richrap	19,417	102	11/17/2015 07:50AM Last Post by deaconfrost
	Geeetech Rumba. Fill does not follow the contours. by AndOsb	629	3	11/17/2015 07:22AM Last Post by AndOsb
	Blobs on layer change by amr_dwarf	8,415	20	11/17/2015 05:07AM Last Post by RRuser
	Vertical ABS cracks by calad	558	6	11/17/2015 02:24AM Last Post by Downunder35m