Subject		Views	Posts	Last Post
	Bad Print Quality by Khilborn	1,833	25	04/24/2015 12:10PM Last Post by ggherbaz
	Random Y-Offset during print & other oddities by ML3D	532	1	04/24/2015 02:28AM Last Post by ML3D
	Yet Another Slic3r Vs. Cura Question by Kafledelius	2,090	11	04/23/2015 11:13PM Last Post by Badkitty
	Filament Diameter by GIGTK	411	2	04/22/2015 09:43PM Last Post by ggherbaz
	i3 prints bigger stuff or prints like it's drunk by Pelm	453	2	04/22/2015 06:51PM Last Post by 3dkarma
	Getting started with i2 prusa mendel by Mr_Summers_ENG	391	2	04/22/2015 06:49PM Last Post by 3dkarma
	Firmware retract with Marlin by WallyL	3,169	5	04/22/2015 07:48AM Last Post by WallyL
	Print dies when voltage drops below 11 volts by 89simmonsalexander	503	5	04/22/2015 03:11AM Last Post by dc42
	Inductive sensor aways OPEN   (Pages: 1 2 3) by gustavogoulart	4,035	64	04/21/2015 09:44AM Last Post by cdru
	ABS print sticks nicely to tape... the tape? Not so much. by kylix.rd	1,985	22	04/20/2015 04:44PM Last Post by alexella
	FRUSTRATING!! - Print quality or weak print by Kafledelius	705	12	04/20/2015 11:43AM Last Post by cat.farmer
	how to choice a good quality UV curing system by colduvdpl	462	1	04/20/2015 07:26AM Last Post by colduvdpl
	Prints not adhering to bed anymore by justashaw	494	5	04/19/2015 02:59PM Last Post by justashaw
	Do NEMA stepper motors go out? by AjaxOfTheRockies	580	4	04/19/2015 01:32PM Last Post by AjaxOfTheRockies
	Why is my extruder suddenly retracting/extruding a ton of filament? by amrbekhit	3,618	12	04/19/2015 10:34AM Last Post by pingnagan
	[Discussion] Distance, default acceleration and "plausible" speed by ishe7ata	4,207	7	04/19/2015 07:50AM Last Post by the_digital_dentist
	layer problems near holes by wes1007	585	3	04/19/2015 03:18AM Last Post by wes1007
	Holes in top layer by barakori	684	6	04/18/2015 06:23PM Last Post by ggherbaz
	X Axis Drifting by DemonsRun	550	4	04/18/2015 04:53PM Last Post by DemonsRun
	Printer pausing/jerking during print by eviltoy	937	5	04/18/2015 03:08PM Last Post by eviltoy
	Panic button? by foul_owl	825	9	04/17/2015 03:17PM Last Post by Kurzaa
	1 out of 10 parts way to high?! by navyblueboss	572	5	04/17/2015 12:28PM Last Post by ggherbaz
	Issues with material warping upwards only on one side of my prints by manorius	655	6	04/17/2015 12:10AM Last Post by manorius
	Infill lacking on first layer _only_ by foul_owl	501	8	04/16/2015 09:29PM Last Post by tmorris9
	Vertical Ridges/waves along sides by prjoe	525	5	04/16/2015 06:22PM Last Post by ggherbaz
	First layer width problem by Badkitty	433	2	04/16/2015 05:57PM Last Post by kre8
	Z Steps by Floyd	577	6	04/16/2015 02:22PM Last Post by chris33
	Slicing Issue, please help a noob by tomy983	516	4	04/16/2015 08:52AM Last Post by tomy983
	printing cilinders with hourglass shape by luc1an	553	4	04/15/2015 10:43AM Last Post by Dirty Steve
	Mid print error traverse by PropellerHat	500	6	04/15/2015 04:41AM Last Post by PropellerHat