Subject		Views	Posts	Last Post
	Can anyone help me figure out why my extruder is skipping like this? by Grifftech	635	7	05/10/2015 08:06PM Last Post by tmorris9
	Possible bed Over heating by TJKing293	366	2	05/10/2015 07:10PM Last Post by dc42
	Start print temperature by Deltatom80	595	4	05/08/2015 03:17PM Last Post by Deltatom80
	Slic3r vs Cura - retraction calibration? by janpenguin	1,751	3	05/07/2015 06:21PM Last Post by itchytweed
	dimensional accuracy cura vs slic3r by ekaggrat	1,500	4	05/06/2015 04:12PM Last Post by chris33
	Extruder slipping? by Ampersands	1,536	3	05/06/2015 03:08PM Last Post by speedeep
	3D Models by monkey12	428	2	05/06/2015 01:19PM Last Post by ggherbaz
	First print NEED ADVICE   (Pages: 1 2) by Ralphy	1,162	54	05/06/2015 08:51AM Last Post by Floyd
	Problem with Z steper motor and Z rod brace ,need advice by Darathy	372	2	05/05/2015 04:18PM Last Post by Darathy
	Suddenly gaps on Z-Axis by Arakon	720	11	05/05/2015 01:17PM Last Post by chris33
	small Blobs/Ridges at corners and randomly on surface? by windcalmer	1,065	8	05/03/2015 10:13PM Last Post by windcalmer
	New nozzle... new problems.... by Kafledelius	697	12	05/03/2015 04:18AM Last Post by Kafledelius
	Regarding attainable accuracy by someoneonly	862	14	05/03/2015 02:13AM Last Post by Epop
	New to 3d printers, have a small issue/question by NerdWurx	758	9	05/03/2015 02:00AM Last Post by Epop
	Help with lines on surface by trikko	434	3	05/02/2015 03:50PM Last Post by trikko
	Heater bed can't keep up by drHEEB	787	13	05/01/2015 04:16PM Last Post by dc42
	Utimaker Original Infill by blauble	468	6	05/01/2015 03:07PM Last Post by blauble
	Positioning Object by tanmn	391	3	04/30/2015 06:43PM Last Post by tanmn
	Z Axis started behaving oddly by spherelance	478	1	04/30/2015 10:50AM Last Post by spherelance
	Extruder problem by foqq	498	6	04/29/2015 08:58PM Last Post by frankvdh
	layer problem by Darathy	565	4	04/29/2015 03:52PM Last Post by Darathy
	first print help needed by supertex	431	2	04/29/2015 12:04PM Last Post by ggherbaz
	Vertical Banding /same printer /same settings / same slicer by prjoe	1,963	9	04/28/2015 12:20PM Last Post by prjoe
	First Print, need suggestions for improvement! by Kdubb	493	3	04/26/2015 07:24PM Last Post by Kdubb
	Noob, new to printing, new folger tech i3.... prints like garbage   (Pages: 1 2) by Hephaestus0000	3,187	31	04/26/2015 06:25PM Last Post by chris33
	Another newbie with printing problems... by rjmusto	441	3	04/26/2015 03:12PM Last Post by rjmusto
	1st print Noob can you believe it? by TheSniper	504	3	04/26/2015 02:02PM Last Post by PedroB
	Printer Suddenly Printing Whiskers and Ridged Walls by Wisar	873	13	04/26/2015 02:09AM Last Post by Wisar
	filament jammed by usman	570	1	04/25/2015 11:52AM Last Post by usman
	Direct drive extruder motor skipping by marsius	5,859	4	04/24/2015 04:12PM Last Post by bbogdanmircea