Subject		Views	Posts	Last Post
	First Layer Rippling problem by CyBer	537	7	06/02/2015 04:09PM Last Post by CyBer
	Red value of position of printer head in print by CyBer	452	1	06/02/2015 01:40AM Last Post by CyBer
	Layer Orientation, help! by mturson	683	11	06/01/2015 10:39PM Last Post by ggherbaz
	Prusa i2 - Wades Extruder Jamming by kevman12	432	3	06/01/2015 07:10PM Last Post by frankvdh
	Raised ripples on surface of flat object by CraigMoberg	2,600	7	06/01/2015 03:39PM Last Post by chris33
	HobbyKing Filament by HGJL2009	1,663	1	06/01/2015 10:01AM Last Post by HGJL2009
	New E3D refuses to extrude by rtrahms	2,015	14	05/31/2015 11:55PM Last Post by greenman100
	Please Help - Z-Axis Quit working - Melzi by pmzielinski	480	5	05/31/2015 05:52PM Last Post by pmzielinski
	Help with some problems! by Guchion	534	6	05/31/2015 05:29PM Last Post by Guchion
	printing issue after replacing nozzle by hamid	441	4	05/31/2015 10:02AM Last Post by Downunder35m
	Bottom comes out curved When printing on painters tape by dnukeg	755	7	05/31/2015 09:50AM Last Post by Downunder35m
	Parts too thick and holes not well defined by 89simmonsalexander	500	3	05/31/2015 04:33AM Last Post by tmorris9
	Stepper Motor Issues by Apple-	405	3	05/31/2015 02:50AM Last Post by Downunder35m
	Scaling bug in Repetier/Slic3r? by CraigMoberg	450	1	05/29/2015 10:10PM Last Post by CraigMoberg
	Skeinforge Settings by jsluke	466	1	05/29/2015 03:48PM Last Post by jsluke
	3D Stuffmaker Mega Prusa Gen1 New Firmware (Marlin) by Downunder35m	775	1	05/29/2015 02:45PM Last Post by Downunder35m
	Prusa i3 x-axis slip - but then not by mikey1248	574	2	05/29/2015 01:57PM Last Post by thetazzbot
	Printing Problems by sirkellsworth	796	11	05/29/2015 12:18PM Last Post by sirkellsworth
	Blobs on prints - Belt tension or software issure? by Kafledelius	643	8	05/29/2015 12:07PM Last Post by Kafledelius
	Printing with Bronzefill by widespreaddeadhead	690	4	05/28/2015 03:07PM Last Post by widespreaddeadhead
	Calibration Piece Analysis by TheHackerArtist	543	2	05/28/2015 02:56PM Last Post by widespreaddeadhead
	Improving edge quality NEED ADVICE by Ralphy	430	3	05/28/2015 02:37PM Last Post by Ralphy
	Can't stop printing midair. by Lapsus	1,821	6	05/28/2015 09:59AM Last Post by Weedz
	Artefacts with Cura and Printrbot metal simple by manorius	527	2	05/28/2015 08:34AM Last Post by ggherbaz
	Strange texture by machapa	445	4	05/27/2015 08:29PM Last Post by machapa
	Avoid crossing perimeters (slow) option? by Ralphy	739	3	05/27/2015 09:30AM Last Post by Ralphy
	Motor vibrates violently by Vashikovich	708	4	05/27/2015 04:55AM Last Post by sarf2k4
	PLA 3D Printing Safety Report by Ink3D.ie	356	2	05/26/2015 08:44PM Last Post by frankvdh
	ABS filament getting 'stuck' about 20 min into a large print. by stevemeetswest	1,690	19	05/26/2015 07:15PM Last Post by stevemeetswest
	Shaxon ABS filament at Frys is crap by thetazzbot	526	1	05/26/2015 02:27PM Last Post by thetazzbot