Welcome! Log In Create A New Profile

Elettronica e meccanica

Discussioni sulle parti elettriche ed elettroniche, motori, endstop, etc. Parliamo di struttura della stampante, pulegge, madreviti, boccole, viti trapezoidali, etc.

Page 10 of 54 Pages:

8 91011 12

Forum List New Topic RSS

	Views	Posts	Last Post
Perdita di passi asse z by Amleto81	514	7	02/12/2018 01:29PM Last Post by Amleto81
Progetto stampante 3d XL by met98	435	1	02/11/2018 01:16PM Last Post by met98
display touch MKS TFT32 by Cencio	397	6	02/11/2018 11:27AM Last Post by Cencio
Heating failed per tronxy x8 by Nabbissimo	579	1	02/11/2018 11:24AM Last Post by Nabbissimo
Nuovi cuscinetti Igus RJ4JP economici [segnalazione] by pivan	867	16	02/08/2018 03:43AM Last Post by immaginaecrea
Driver che scaldano by Apeks	666	9	02/06/2018 04:59PM Last Post by Apeks
Endstops scollegano Arduino USB by pietro_c	381	11	02/06/2018 04:47AM Last Post by pietro_c
ultratronics BLTouch e LAN by Libbbio	1,218	18	02/05/2018 02:51PM Last Post by MagoKimbra
Raps 128 step per unit by pivan	705	13	02/05/2018 05:44AM Last Post by MagoKimbra
DRIVER TMC2100 by ADRIANO3D	1,282	12	01/30/2018 10:18AM Last Post by obelix58
auto livellamento asse Z (Pages: 1 ... 5 6 7) by Marck80	17,602	181	01/30/2018 09:58AM Last Post by silvanopas
Optoisolatori: Prototipo su breadboard by Alessandro3DP	502	10	01/27/2018 04:42AM Last Post by volcane
MKS Gen 1.4 + Full Graphic smart controller - MK4DUO 4.3.2 by laudix	1,068	8	01/25/2018 10:36AM Last Post by laudix
Problema con scheda SD Reprap discount fullgraphic LCD by Seifer89	404	1	01/21/2018 06:07PM Last Post by Seifer89
Dubbi su dimensionamento delta by karnhack	359	2	01/20/2018 12:36AM Last Post by fenix
Consiglio upgrade da scheda GT2560 (Geeetech) a ??? (magari 32 bit) by Noisemaker	1,313	7	01/19/2018 09:24AM Last Post by Sicon
[CoreXY] Quali profilati scegliere per il telaio? (T-Slot, V-Slot, etc.) by Noisemaker	515	1	01/16/2018 05:49AM Last Post by Noisemaker
Regolazione DRV 8825 by Apeks	816	7	01/13/2018 04:26PM Last Post by Apeks
AutoSpegnimento a fine stampa da SD by ilmagowalter	559	2	01/11/2018 08:31AM Last Post by ilmagowalter
Nema 17 Titan Extruder Vref by Micron792	457	1	01/09/2018 05:50PM Last Post by Micron792
Aiuto RUMBA by the_duke	390	1	01/06/2018 08:51AM Last Post by the_duke
Lettura errata temperatura by Teo234	347	1	12/31/2017 09:51AM Last Post by Teo234
prusa i3 mk2 geeetech CAMBIARE DISPLAY CON UNO PIU' LUNGO? by roberto76milano	474	4	12/27/2017 10:05AM Last Post by MagoKimbra
Sostituzione driver A4988 con TMC 2100 by brunosso	1,099	1	12/25/2017 12:35PM Last Post by brunosso
Problema viti trapezie su prusa i3 by Teo234	711	7	12/25/2017 09:53AM Last Post by Teo234
URGENTE problema asse z [RISOLTO] by Simone98	504	7	12/22/2017 05:38PM Last Post by Simone98
RAMPS 1.4 con motori NEMA 23 ??? by DOM	529	1	12/21/2017 11:48AM Last Post by DOM
Ramps 1.4- full lcd- tmc 2030 by gigahertz77	631	5	12/19/2017 01:50PM Last Post by gigahertz77
Problema viti trapezie su prusa i3 by Teo234	631	2	12/18/2017 10:59AM Last Post by Luca_Benedetto
Cuscinetti e barre, riflessione sui materiali (Pages: 1 2) by Elstak	2,677	49	12/17/2017 05:38PM Last Post by Erik83

Page 10 of 54 Pages:

8 91011 12

Elettronica e meccanica

auto livellamento asse Z (Pages: 1 ... 5 6 7)

Cuscinetti e barre, riflessione sui materiali (Pages: 1 2)