Upload error, stk500_getsync(): not in sync: resp=0xee February 04, 2013 05:57PM |
Registered: 11 years ago Posts: 10 |
Re: Upload error, stk500_getsync(): not in sync: resp=0xee February 04, 2013 06:03PM |
Registered: 11 years ago Posts: 349 |
Re: Upload error, stk500_getsync(): not in sync: resp=0xee February 04, 2013 06:06PM |
Registered: 11 years ago Posts: 10 |
Re: Upload error, stk500_getsync(): not in sync: resp=0xee February 04, 2013 06:42PM |
Registered: 11 years ago Posts: 10 |
Re: Upload error, stk500_getsync(): not in sync: resp=0xee February 04, 2013 06:47PM |
Registered: 13 years ago Posts: 632 |
Re: Upload error, stk500_getsync(): not in sync: resp=0xee February 04, 2013 06:48PM |
Registered: 11 years ago Posts: 349 |
Re: Upload error, stk500_getsync(): not in sync: resp=0xee February 04, 2013 06:51PM |
Registered: 11 years ago Posts: 10 |
Re: Upload error, stk500_getsync(): not in sync: resp=0xee February 04, 2013 08:22PM |
Registered: 11 years ago Posts: 10 |
Re: Upload error, stk500_getsync(): not in sync: resp=0xee February 05, 2013 07:00AM |
Registered: 13 years ago Posts: 7,616 |
Quote
That error is gone but now i have "Yikes! Invalid device signature. double check connection and try again, or use -F to override"
Quote
P.S. Lot of talk all over the place about the 10 sec reset button. According to Wiki this is only for boards older than 1.3a.
Generation 7 Electronics | Teacup Firmware | RepRap DIY |
Re: Upload error, stk500_getsync(): not in sync: resp=0xee February 05, 2013 01:53PM |
Registered: 11 years ago Posts: 10 |
Re: Upload error, stk500_getsync(): not in sync: resp=0xee February 05, 2013 07:22PM |
Registered: 11 years ago Posts: 349 |
Re: Upload error, stk500_getsync(): not in sync: resp=0xee February 08, 2013 06:46AM |
Registered: 13 years ago Posts: 7,616 |
Quote
lazzymonk
I use [www.ebay.co.uk] great kit works great.
Quote
Surely that is not it.
Tools --> Board -->Sanguini W/Atmega 644P.
Quote
Baud rate 115200 in the config.h and 35400 in the board.txt as described in the Wiki.
Generation 7 Electronics | Teacup Firmware | RepRap DIY |
Re: Upload error, stk500_getsync(): not in sync: resp=0xee February 09, 2013 08:07PM |
Re: Upload error, stk500_getsync(): not in sync: resp=0xee February 13, 2013 09:43AM |
Registered: 11 years ago Posts: 10 |
Re: Upload error, stk500_getsync(): not in sync: resp=0xee February 14, 2013 06:59AM |
Registered: 13 years ago Posts: 7,616 |
Generation 7 Electronics | Teacup Firmware | RepRap DIY |
Re: Upload error, stk500_getsync(): not in sync: resp=0xee February 14, 2013 08:28AM |
Registered: 11 years ago Posts: 10 |
Re: Upload error, stk500_getsync(): not in sync: resp=0xee February 15, 2013 06:42AM |
Registered: 13 years ago Posts: 7,616 |
Quote
didnt want to turn the printer off so that it would loose its print position
Generation 7 Electronics | Teacup Firmware | RepRap DIY |
Re: Upload error, stk500_getsync(): not in sync: resp=0xee February 15, 2013 11:02AM |
Registered: 11 years ago Posts: 10 |
Re: Upload error, stk500_getsync(): not in sync: resp=0xee February 15, 2013 04:59PM |
Registered: 11 years ago Posts: 273 |
Re: Upload error, stk500_getsync(): not in sync: resp=0xee February 15, 2013 05:20PM |
Registered: 11 years ago Posts: 10 |