Just printed the first print. October 10, 2015 11:45AM |
Registered: 8 years ago Posts: 14 |
Re: Just printed the first print. October 10, 2015 02:06PM |
Registered: 10 years ago Posts: 541 |
Re: Just printed the first print. October 10, 2015 02:12PM |
Admin Registered: 17 years ago Posts: 7,879 |
Re: Just printed the first print. October 10, 2015 02:34PM |
Registered: 8 years ago Posts: 14 |
Re: Just printed the first print. October 10, 2015 05:12PM |
Admin Registered: 17 years ago Posts: 7,879 |
Re: Just printed the first print. October 11, 2015 06:56AM |
Registered: 8 years ago Posts: 14 |
Re: Just printed the first print. October 11, 2015 08:28AM |
Admin Registered: 17 years ago Posts: 7,879 |
Re: Just printed the first print. October 11, 2015 09:26AM |
Registered: 8 years ago Posts: 14 |
Re: Just printed the first print. October 11, 2015 04:38PM |
Admin Registered: 17 years ago Posts: 7,879 |
Re: Just printed the first print. October 13, 2015 01:53PM |
Registered: 8 years ago Posts: 14 |
Re: Just printed the first print. October 13, 2015 06:09PM |
Admin Registered: 17 years ago Posts: 7,879 |
Re: Just printed the first print. October 14, 2015 01:01PM |
Registered: 8 years ago Posts: 14 |
Re: Just printed the first print. October 14, 2015 03:37PM |
Admin Registered: 17 years ago Posts: 7,879 |
Re: Just printed the first print. October 23, 2015 05:43AM |
Registered: 8 years ago Posts: 14 |
Re: Just printed the first print. October 24, 2015 05:52AM |
Registered: 10 years ago Posts: 541 |
Re: Just printed the first print. October 24, 2015 08:20AM |
Registered: 8 years ago Posts: 14 |
Re: Just printed the first print. October 25, 2015 06:41AM |
Registered: 10 years ago Posts: 541 |
Re: Just printed the first print. October 25, 2015 12:15PM |
Registered: 8 years ago Posts: 14 |
Re: Just printed the first print. October 25, 2015 03:41PM |
Admin Registered: 17 years ago Posts: 7,879 |
Re: Just printed the first print. October 25, 2015 05:18PM |
Registered: 8 years ago Posts: 14 |
Re: Just printed the first print. October 25, 2015 08:25PM |
Admin Registered: 17 years ago Posts: 7,879 |
Re: Just printed the first print. October 27, 2015 04:05AM |
Registered: 10 years ago Posts: 541 |
Filament: Reprappertech.com 3mm Grey PLA Slicer: Slic3r-1.2.9 Hotend temperature: 200C Heated Bed temperature: 70C Layer Height: 0.2mm Line Width: 0.5mm (all line widths in Slic3r set to this value) Perimeters: 2 minimum Bridge Flow ratio: 0.9 Print Speed: 40mm/sec Cooling: Fan on 100% after first layer and below 240 sec layer time. 5 sec minimum layer time.This is the first acceptable Marvin I have been able to print and it reinforces my earlier comment that bridging and overhang printing ability is as much down to material as technique. nophead's choice of Faberdashery PLA for the sample included with the kit is wise as a low-risk solution. I think the Reprappertech filament demonstrates that there are good filaments coming out of China and they are a company who are serious about filament development.
Re: Just printed the first print. October 28, 2015 03:58AM |
Registered: 8 years ago Posts: 14 |
Re: Just printed the first print. October 28, 2015 07:08AM |
Registered: 10 years ago Posts: 541 |
Re: Just printed the first print. October 29, 2015 12:37PM |
Registered: 8 years ago Posts: 14 |
Re: Just printed the first print. October 29, 2015 02:19PM |
Admin Registered: 17 years ago Posts: 7,879 |
Re: Just printed the first print. October 29, 2015 03:13PM |
Registered: 8 years ago Posts: 14 |
Re: Just printed the first print. October 29, 2015 05:28PM |
Registered: 10 years ago Posts: 541 |
Re: Just printed the first print. November 01, 2015 10:45AM |
Registered: 10 years ago Posts: 541 |
Re: Just printed the first print. November 01, 2015 06:39PM |
Registered: 8 years ago Posts: 14 |