Re: [problemy] - kalibrace September 07, 2014 12:59PM |
Registered: 11 years ago Posts: 24 |
Re: [problemy] - kalibrace September 11, 2014 02:39PM |
Registered: 10 years ago Posts: 20 |
Re: [problemy] - kalibrace September 11, 2014 03:17PM |
Moderator Registered: 11 years ago Posts: 1,038 |
Re: [problemy] - kalibrace September 11, 2014 04:00PM |
Registered: 11 years ago Posts: 120 |
Re: [problemy] - kalibrace September 11, 2014 04:29PM |
Registered: 10 years ago Posts: 20 |
Re: [problemy] - kalibrace September 11, 2014 04:48PM |
Moderator Registered: 11 years ago Posts: 1,038 |
Re: [problemy] - kalibrace September 11, 2014 05:15PM |
Registered: 10 years ago Posts: 20 |
Re: [problemy] - kalibrace September 11, 2014 05:42PM |
Moderator Registered: 12 years ago Posts: 803 |
Re: [problemy] - kalibrace September 14, 2014 04:52AM |
Registered: 10 years ago Posts: 20 |
Re: [problemy] - kalibrace October 28, 2014 04:11PM |
Registered: 10 years ago Posts: 46 |
Re: [problemy] - kalibrace January 08, 2015 04:05PM |
Registered: 11 years ago Posts: 151 |
jak pise Bajn,bowden je osidnej,zmetek se napina a muze se napruzit a chovat se jak pero.Quote
jeninicicek
Tak jsem chvíli ladil a upravoval(zkrátil bowden-úplně seho zbavit nejde..., vyladil config co mi šlo - příloha, trošku přitlačil na podávání...), ale stále to není ono(viz příloha), nějaký tip čím pohnout? Prostě po přesunu boulička, vlákna už to netahá, ale pořád je poznat, kde byly přesuny... nějaký tip, co kde?
Re: [problemy] - kalibrace March 06, 2015 08:23AM |
Registered: 10 years ago Posts: 10 |
Re: [problemy] - kalibrace March 06, 2015 08:41AM |
Moderator Registered: 11 years ago Posts: 1,038 |
Re: [problemy] - kalibrace March 06, 2015 08:52AM |
Registered: 10 years ago Posts: 10 |
Re: [problemy] - kalibrace March 06, 2015 09:49AM |
Moderator Registered: 11 years ago Posts: 1,038 |
Re: [problemy] - kalibrace March 10, 2015 05:35PM |
Registered: 9 years ago Posts: 2 |
Re: [problemy] - kalibrace April 25, 2015 05:27PM |
Registered: 10 years ago Posts: 24 |
Re: [problemy] - kalibrace April 25, 2015 05:38PM |
Registered: 11 years ago Posts: 748 |
Re: [problemy] - kalibrace April 26, 2015 05:16AM |
Registered: 10 years ago Posts: 24 |
Re: [problemy] - kalibrace April 26, 2015 05:55AM |
Registered: 10 years ago Posts: 24 |
Re: [problemy] - kalibrace April 26, 2015 08:21AM |
Moderator Registered: 11 years ago Posts: 1,038 |
Re: [problemy] - kalibrace April 26, 2015 08:27AM |
Moderator Registered: 11 years ago Posts: 1,038 |
Quote
Kouďák
omlouvám se za tolik stejných zpráv problém s internetem a nevím jak je vymazat
Re: [problemy] - kalibrace April 26, 2015 05:55PM |
Registered: 10 years ago Posts: 24 |
Re: [problemy] - kalibrace April 27, 2015 05:04AM |
Moderator Registered: 11 years ago Posts: 1,038 |
Quote
Kouďák
takže pro trysku 0.4 je ideální nastavený výšky vrstvy kolik?
manuálním posuvem x y ale i z sedí aspoň podle posledních měření ale dám krokování na 4000
no jinak když tisknu kostku 20x20x20 tak mám rozměry cca 16,7 x16,7 a výšku už ani nevím musím zkusit znovu vytisknout
Re: [problemy] - kalibrace April 30, 2015 04:53AM |
Registered: 10 years ago Posts: 24 |
Re: [problemy] - kalibrace April 30, 2015 04:55AM |
Registered: 10 years ago Posts: 24 |
Re: [problemy] - kalibrace April 30, 2015 06:23AM |
Moderator Registered: 11 years ago Posts: 1,038 |
Quote
Kouďák
jo a taky sem dal chladiče na drivery tak nevim jestli to tomu taky nepřispělo
Re: [problemy] - kalibrace April 30, 2015 06:36AM |
Registered: 10 years ago Posts: 24 |
Re: [problemy] - kalibrace April 30, 2015 06:52AM |
Moderator Registered: 11 years ago Posts: 1,038 |
Quote
Kouďák
Tak pánové s radostí oznamuji, že tisku přesné rozměry
Re: [problemy] - kalibrace April 30, 2015 07:25AM |
Registered: 10 years ago Posts: 24 |