Prusa i3 Rework Gregstruder - Inconsistent Flow January 10, 2015 02:22PM |
Registered: 9 years ago Posts: 10 |
Re: Prusa i3 Rework Gregstruder - Inconsistent Flow January 10, 2015 05:03PM |
Registered: 10 years ago Posts: 466 |
Re: Prusa i3 Rework Gregstruder - Inconsistent Flow January 10, 2015 05:08PM |
Registered: 9 years ago Posts: 10 |
Re: Prusa i3 Rework Gregstruder - Inconsistent Flow January 10, 2015 05:24PM |
Registered: 10 years ago Posts: 477 |
Quote
bergerab
Yes I've always used one screw just because long M3 screws are hard to find around me. I'll order some online, but for now I just added a zip-tie keeping the other side tight.
Re: Prusa i3 Rework Gregstruder - Inconsistent Flow January 10, 2015 05:32PM |
Registered: 9 years ago Posts: 10 |
Re: Prusa i3 Rework Gregstruder - Inconsistent Flow January 10, 2015 06:00PM |
Registered: 10 years ago Posts: 477 |
Quote
bergerab
Do you think you could take a look at my acceleration/jerk/feedrates and judge if they are a little too high/low? I couldn't find any good guides to fine tune those values in the firmware.
Re: Prusa i3 Rework Gregstruder - Inconsistent Flow January 10, 2015 06:37PM |
Registered: 9 years ago Posts: 10 |
Re: Prusa i3 Rework Gregstruder - Inconsistent Flow January 10, 2015 07:55PM |
Registered: 9 years ago Posts: 10 |
Re: Prusa i3 Rework Gregstruder - Inconsistent Flow January 11, 2015 06:50PM |
Registered: 9 years ago Posts: 8 |
Re: Prusa i3 Rework Gregstruder - Inconsistent Flow January 11, 2015 06:58PM |
Registered: 9 years ago Posts: 8 |
Re: Prusa i3 Rework Gregstruder - Inconsistent Flow January 11, 2015 07:44PM |
Registered: 10 years ago Posts: 477 |
Quote
bergerab
Just as an update, I've ordered all new hardware for my Rework extruder. I should get it by Wednesday. I'll update this post once I test with the new hardware to see if this resolved my issue.
Re: Prusa i3 Rework Gregstruder - Inconsistent Flow January 11, 2015 08:01PM |
Registered: 9 years ago Posts: 10 |
Re: Prusa i3 Rework Gregstruder - Inconsistent Flow January 13, 2015 12:42PM |
Registered: 9 years ago Posts: 10 |
Re: Prusa i3 Rework Gregstruder - Inconsistent Flow January 13, 2015 01:28PM |
Registered: 10 years ago Posts: 466 |
Re: Prusa i3 Rework Gregstruder - Inconsistent Flow January 13, 2015 06:41PM |
Registered: 9 years ago Posts: 10 |
Re: Prusa i3 Rework Gregstruder - Inconsistent Flow January 13, 2015 10:13PM |
Registered: 9 years ago Posts: 10 |
Re: Prusa i3 Rework Gregstruder - Inconsistent Flow January 13, 2015 10:58PM |
Registered: 9 years ago Posts: 10 |
Re: Prusa i3 Rework Gregstruder - Inconsistent Flow January 14, 2015 02:55AM |
Registered: 10 years ago Posts: 477 |
Re: Prusa i3 Rework Gregstruder - Inconsistent Flow January 14, 2015 10:31AM |
Registered: 10 years ago Posts: 466 |