Marlin v2.17

Hi new I wanted to check settings in printer to be able to check and /or set flow/stps etc but when entering M503 this is what i am now getting if anyone could help decipher where to start i did have a problem when first bought and i had to download and upload new firmware i think v1.6 on there originally,and M503 gave you back settings but hiding steps or something you needed to calibrate but now i just get this back although printer seams to work fine but sizing of anything is off.
Many Thanks if anyone could decipher and at least tell me where to start.

reply from M503

SENDING:M503
ok T0:23.67 /0.00 B:23.52 /0.00 T0:23.67 /0.00 T1:23.48 /0.00 @:0 B@:0 @0:0 @1:0
Exception in thread read thread:
Traceback (most recent call last):
File "printrun\printcore.py", line 333, in _readline
File "printrun\printcore.py", line 329, in _readline_nb
File "serial\serialwin32.py", line 295, in read
serial.serialutil.SerialException: GetOverlappedResult failed (PermissionError(13, 'Access is denied.', None, 5))

During handling of the above exception, another exception occurred:

Traceback (most recent call last):
File "threading.py", line 932, in _bootstrap_inner
File "threading.py", line 870, in run
File "printrun\printcore.py", line 420, in _listen
File "printrun\printcore.py", line 354, in _readline
IndexError: tuple index out of range

Disconnecting after 4 failed writes.

No such thing as marlin 2.17

List of all marlin versions so far

1.0.0-beta
1.0.1
1.0.2
1.0.2-1
1.0.2-2
1.0.2-3
1.1.0
1.1.0-RC1
1.1.0-RC2
1.1.0-RC3
1.1.0-RC4
1.1.0-RC5
1.1.0-RC6
1.1.0-RC7
1.1.0-RC8
1.1.1
1.1.2
1.1.3
1.1.4
1.1.5
1.1.6
1.1.7
1.1.8
1.1.9
1.1.9.1
1.1.9.2
2.0.0
2.0.0.1
2.0.1
2.0.1.1
2.0.2
2.0.2.1
2.0.3
2.0.3.1
2.0.4
2.0.4.1
2.0.4.2
2.0.4.3
2.0.4.4
2.0.4.5
2.0.5
2.0.5.1
2.0.5.2
2.0.5.3
2.0.5.4
2.0.5.5
2.0.6
2.0.6.1
2.0.6.2
2.0.7
2.0.7.1
2.0.7.2
2.0.7.3
2.0.8
2.0.8.1
2.0.8.2
2.0.8.3
2.0.8.4
2.0.9
2.0.9.1
2.0.9.2
2.0.9.3
2.0.9.4
2.0.9.5
2.0.9.6
2.0.9.7
2.0.9.8
2.1
2.1.0.1
2.1.0.2
2.1.1
2.1.1.1
2.1.1.2
2.1.2
2.1.2.1

Use a serial program such as vscode serial monitor

Make sure to send M503 in uppercase without making typos (pronterface automatically turns the input into uppercase for you)

Also how old is your pronterface? Perhaps it needs updating [github.com]

Edited 1 time(s). Last edit at 01/08/2024 08:48PM by Dust.

Sorry

Version
FIRMWARE_NAME:Marlin 2.0.9.2 (Jul 13 2022 17:24:43) SOURCE_CODE_URL:github.com/MarlinFirmware/Marlin PROTOCOL_VERSION:1.0 MACHINE_TYPE:TRONXY_F446 EXTRUDER_COUNT:2 UUID:cede2a2f-41a2-4748-9b12-c55c62f367ff
CapERIAL_XON_XOFF:0
Cap:BINARY_FILE_TRANSFER:0
Cap:EEPROM:1
Cap:VOLUMETRIC:1
Cap:AUTOREPORT_POS:0
Cap:AUTOREPORT_TEMP:1
CapROGRESS:0
CapRINT_JOB:1
Cap:AUTOLEVEL:0
Cap:RUNOUT:1
Cap:Z_PROBE:0
Cap:LEVELING_DATA:0
Cap:BUILD_PERCENT:0
CapOFTWARE_POWER:1
Cap:TOGGLE_LIGHTS:0
Cap:CASE_LIGHT_BRIGHTNESS:0
Cap:EMERGENCY_PARSER:0
Cap:HOST_ACTION_COMMANDS:0
CapROMPT_SUPPORT:0
CapDCARD:1
Cap:REPEAT:0
CapD_WRITE:1
Cap:AUTOREPORT_SD_STATUS:0
Cap:LONG_FILENAME:0
Cap:THERMAL_PROTECTION:1
Cap:MOTION_MODES:0
Cap:ARCS:1
Cap:BABYSTEPPING:1
>>> M503
SENDING:M503
ok T0:23.01 /0.00 B:22.54 /0.00 T0:23.01 /0.00 T1:22.93 /0.00 @:0 B@:0 @0:0 @1:0

Using Pronterface Printrun 2.0.0.orc8

Hi Dust sent reply via forum with correct version M503 just repeats the line i have shown now but does'nt seem to report anything.