Re: Prusa i3 Complete Kit August 06, 2014 06:47AM |
Registered: 10 years ago Posts: 82 |
Re: Prusa i3 Complete Kit August 07, 2014 05:20PM |
Registered: 9 years ago Posts: 3 |
Re: Prusa i3 Complete Kit August 08, 2014 03:23AM |
Registered: 9 years ago Posts: 10 |
Re: Prusa i3 Complete Kit August 08, 2014 07:21AM |
Registered: 9 years ago Posts: 3 |
Re: Prusa i3 Complete Kit August 08, 2014 07:44AM |
Registered: 10 years ago Posts: 82 |
Re: Prusa i3 Complete Kit August 11, 2014 08:02AM |
Registered: 9 years ago Posts: 3 |
Re: Prusa i3 Complete Kit September 02, 2014 11:03AM |
Registered: 10 years ago Posts: 82 |
Re: Prusa i3 Complete Kit September 06, 2014 01:50PM |
Registered: 9 years ago Posts: 16 |
Re: Prusa i3 Complete Kit September 08, 2014 10:15AM |
Registered: 10 years ago Posts: 82 |
Re: Prusa i3 Complete Kit September 09, 2014 03:34AM |
Registered: 9 years ago Posts: 16 |
Re: Prusa i3 Complete Kit September 09, 2014 06:51AM |
Registered: 9 years ago Posts: 16 |
Re: Prusa i3 Complete Kit September 09, 2014 03:20PM |
Registered: 10 years ago Posts: 82 |
Re: Prusa i3 Complete Kit September 13, 2014 06:48AM |
Registered: 9 years ago Posts: 16 |
Re: Prusa i3 Complete Kit September 14, 2014 08:22AM |
Registered: 9 years ago Posts: 14 |
Re: Prusa i3 Complete Kit September 14, 2014 11:33AM |
Registered: 9 years ago Posts: 16 |
Re: Prusa i3 Complete Kit September 14, 2014 04:49PM |
Registered: 9 years ago Posts: 14 |
Quote
yannik
I learned this weekend: The E3D fan must run always with 100%. Also connect this fan to the 12V power.
Pherhaps there is a connection on the board which enables the fan when the printing starts?
I had connected the fan to the controlled output, ant this caused the E3d to jam.
Re: Prusa i3 Complete Kit September 15, 2014 08:11AM |
Registered: 10 years ago Posts: 82 |
Re: Prusa i3 Complete Kit September 15, 2014 10:54AM |
Registered: 9 years ago Posts: 16 |
Quote
craftcadet
Quote
yannik
I learned this weekend: The E3D fan must run always with 100%. Also connect this fan to the 12V power.
Pherhaps there is a connection on the board which enables the fan when the printing starts?
I had connected the fan to the controlled output, ant this caused the E3d to jam.
Thanks for the info. That sucks shame that information was not obvious.
I really like this kit and i expected to do a large amount of research to build. I am finding that within rep-rap there are huge amount of variations of one style of printer and that is what i like about open source you get what you want. but it does tend to breed errors and mishaps. having this forum dedicated to this kit is excellent.
Re: Prusa i3 Complete Kit September 15, 2014 11:40AM |
Registered: 10 years ago Posts: 82 |
Re: Prusa i3 Complete Kit September 15, 2014 09:45PM |
Registered: 9 years ago Posts: 1 |
Re: Prusa i3 Complete Kit September 16, 2014 05:45AM |
Registered: 10 years ago Posts: 82 |
Re: Prusa i3 Complete Kit September 22, 2014 07:40AM |
Registered: 9 years ago Posts: 6 |
Re: Prusa i3 Complete Kit September 22, 2014 12:09PM |
Registered: 10 years ago Posts: 82 |
Re: Prusa i3 Complete Kit September 22, 2014 01:08PM |
Registered: 9 years ago Posts: 6 |
Re: Prusa i3 Complete Kit September 24, 2014 04:52PM |
Registered: 9 years ago Posts: 12 |
Re: Prusa i3 Complete Kit September 25, 2014 09:47AM |
Registered: 9 years ago Posts: 34 |
Re: Prusa i3 Complete Kit September 25, 2014 11:27AM |
Registered: 10 years ago Posts: 82 |
Re: Prusa i3 Complete Kit September 25, 2014 11:28AM |
Registered: 10 years ago Posts: 82 |
Re: Prusa i3 Complete Kit September 25, 2014 03:00PM |
Registered: 9 years ago Posts: 12 |
Re: Prusa i3 Complete Kit September 25, 2014 03:30PM |
Registered: 10 years ago Posts: 82 |
It sounds correct. Sometimes if I have the printer connected in Pronterface it will time-out during the upload. But if it gets through the upload ok (i.e. says "Done Uploading" without any error messages) it should be ok. I suggest trying Pronterface to check it's not a compatibility issue with Repetier (although I know someone who's using Repetier ok with one of my printers).Quote
When I loaded the config file onto the board I had sent it from arduino to the board with the ramps still attached and all power on but I was not connected to the Repetier software, does this sound correct or have I done something wrong?