Hello Alan missed that one , thank bro =) this is my beast check this outby Elidor - CoreXY Machines
Hi i have XY core and im using max endstop on the x axis with the previous marlin firmware i didnt have ant issue i got the latest marlin yesterday no when im pressing X home the system dosent move x axis and set it as a zero point from there i can move the x axis only to the negetive side any suggestions pleaseby Elidor - CoreXY Machines
HI thank you alot for the quick support =) i was trying what you have adviced ... it working great first.. home X0 Y0 G30 G32 Print... start g code G1 X0 Y0 on slicer some idea for other approch no min endstop 1. user cannot move z axis or home z axis when connect printer 2. the system will automaticly move up z axis by 5 mm or so on power up ( like delta home on start ) in orderby Elidor - Repetier
Hello Roland i have the same iisue but im not getting one thing , im trying to set auto level for a month now my setup is latest firmware (from today) z min end stop z probe on pin 47 (capacitive sensor) after im G28 , im sending G30 then the probe probe for hight then im sending g32 and on the second probe point im getting z probe error and that is becaouse the z min endstop triggersby Elidor - Repetier
Hello repetier every thing is going great , execpt that im trying to run auto level ( i did some reading and i understand that some other ppl have this kind of issue ) im getting 4 point probing and did that for 4 time using this commend G32 PS2 P0 AND P1 AND P2 AND P3 its seems that when im trying to print i get and unlevel surface for example on the -x SIDE THE NUZZLE GOING DOWN AND ON THEby Elidor - Repetier
Hello repetier im trying to understand ... when im in config.h i can find the code for z probing ? so do i have to copy the code to config.h from z probe manual on your site ? regards elidorby Elidor - Repetier
Hi what do you mean with a lot more infill ?? i guess you do that with other hotend as well .by Elidor - General
Hi Yes , soon ill post on wiki .by Elidor - General
Hello to all here is a first video fot the R3D hotend on my twister . my setup is direct drive extruder with 600 mm theflon tube , 72oz stepper motor speed - 150 -180 mm/sec temp - 195 no licking at all and very little oozing elidor revision3dby Elidor - General
HI guys thank you for the comments . the idea is hotend without an active cooling (fan) and very low frication the thing is to direct the heating exactly where it should go and stay there . the nuzzle just slide in without screwing in order to make more contact with the block the block made from alum' 6062 the heatsink act like a thermal barrier and helps to keep the peek cooler (6062 aluby Elidor - General
hello finally.... =) this is my new design for hotend ill post specification soonby Elidor - General
Hello repetier first i would like to thank you for the great support i was checking there is no short ,im working on my new design for the delta and i think that the wire is too long and i think that the ressitance is too high because the long running (wire) it atlist 1 meter long what do you think ? thank you elidorby Elidor - Repetier
HI im was trying number 1 and again im getting 500 deg im trying for aweek im lost elidorby Elidor - Repetier
hI NO ITS NOT , HOPE TO SEE THIS SUPPORT SOON THANK YOU FOR TRYING BEST REGARDS ELIDOR ZAMIRby Elidor - Repetier
cool thank you i would like allso to help to translat repetier host to hebrew , where do i begin ? thank you =)by Elidor - Repetier
Hello repetier im using this one 100K ohm (EPCOS B57560G104F NTC THERMISTOR) the think is that im using the same type on my bed and im getting a good reading but not on the hotend - selection number 5 on bed and on hot end what im doing wrong ? thank you alot elidorby Elidor - Repetier
Hello im using repeptier firmware and i have problem with epcos FFF104 table cant find the table can i get the table please best regardsby Elidor - Repetier
Hello is there out there a thermisitor that could work up to 400 celsius ? thank youby Elidor - General
HI im using 3 mm mirror for my print bed , i used to have issue sometimes with small parts and very long prints wrapping and other stuff . now im cleaing the mirror with chloride or hydrogen peroxide on a paper towel and OMG i can print at 55 deg,. i can print big parts , small parts and very small parts =) with no wrapping at all and other issues , i had a printing that last like 7 hours.by Elidor - General
Hello pruse love this design =) - i belive in keep it simple and nice i have a new design for extruder that im testing right now my extruder very easy to assamble ' doesn't need cooling at all and can work with 400 celsius no problem . i can print 200 mm per sec with 190 celsius with direct drive . ill post pictures soon elidorby Elidor - General
HI currently im using a 3m belt and i would like to try 2m belt does someone have some experience with them ? looks like they can slip easily on fast printing (250 mm/sec ) any help will appreciate elidorby Elidor - General
Hi Well on 9 it was ok but the latest version is really bad But we can not complain the guys doing a great job I think the problem is that the extruder not working on the right speed When printing fast . Now I'm printing again with 8.4 and the print are nice on 80 mm/sec Faster then that and the infill not so good When I was trying slicer 9 on 150 mm/sec I got a nice printing but the solidby Elidor - General
Hello when im printing with slicer 042 i get beautifull printing but seens i moved to 09.... slicer i get the most ugliest prints can someone direct me what im doing wrong ?? i have issue with missing steps issue with retraction solid surface no solid at all regardsby Elidor - General
hello im working im working on a new online store , i will sale orca with proffesional parts after with few ajustment for easy printing and calbartion i made a custom pullyes for z axis the pulleyes are with threaded m8 bore for z axis - z axis is now super straight and smooth movments . im using a 9 mm M3 belts for more allso i have develope a new extruder that based on V9 extruder ,by Elidor - General
Hi thank you all =) so i have a ressistor 10 ohms 5 watt is this will do the work to get 0.5 amp load on 5 volt rail thanksby Elidor - General
Hi is there any solution for support in slicer... ? if not in which program can i add this feature ? regards elidorby Elidor - General