Show all posts by user
(RepRap en Français)
Page 1 of 1 Pages: 1
Results 1 — 17 of 17
Hi Dmould,
it's exactly this problem ^^
thanks for your advices, i will try to cool the zone with a fan, i've added a feature request for S3D regarding selective fan control but ... i doubt they will add this feature.
by
dapsaille
-
Ormerod
Hello,
i'm pretty happy with my settings and hardware setup except one thing ..
everytime i print a "closed angled" surface i get abs burn on the layers ..
i've attached two pics of the problem, do you have any idea ?
Abs homemade
230C hotend
110C bed
Ormerod 0.5 nozzle
Simplify3d
by
dapsaille
-
Ormerod
that's perfect
thanks a lot
by
dapsaille
-
Ormerod
Does anyone have a stl for hotend mount for e3dv6 with dc42's hot end board V2 support ?
(i'm not really good in 3d software)
by
dapsaille
-
Ormerod
EDIT = sorry .... i left my ormerod alone for a long time and i've forgotten basics ...
i homed XYZ then tryed to configure Z height ... it works much better when homing X and Y only
Hi,
i've just upgraded to this firmware and i cannot calibrate the Z probe, i can't gest below 0 for the Z axis ..
i used G92 Z0 than i clicked on -0.1 for Z axis to find the right probe point but it don't
by
dapsaille
-
Ormerod
thanks everyone
M208 X200 Y215 Z200 ; set axis maxima (adjust to suit your machine)
M208 X0 Y-15 S1 ; set axis minimum (adjust to make X=0 the edge of the bed)
did the trick ^^
by
dapsaille
-
Ormerod
Treito Sorry if my words seems too rude, i didn't want to blame or hurt anyone, my english is a little .. rusty
Thanks to everyone for all thoose informations, i will read/test/undestand (i hope) all this stuff in the evening.
by
dapsaille
-
Ormerod
yes sorry, i've edited my post ^^
anyway, i don't understand why my printhead stay at the exact same place (out of the bed) when i modify axis minima .
by
dapsaille
-
Ormerod
thanks i'm trying thoose options
dumb question = how can i say to my printer to move to x0 y0 for exemple ?
edit = with this config
"
M208 X200 Y205 Z200 ; set axis maxima (adjust to suit your machine)
M208 X0 Y56 S1 ; set axis minimum (adjust to make X=0 the edge of the bed)
"
in web interface i can't got under 56 for y position but physically the head is at the exact same pl
by
dapsaille
-
Ormerod
Hello,
everytime i print something with my ormerod 2 (gcode generated by simplify3d) the print start out of bed on the left side (2cm outside) ...
How can i "center" the print ? i've found many options in simplify3d but it doesn't seem to work (Toolhead offsets, global offsets) and/or i don't understand them.
I'd prefer to configure it directly on my ormerod trough config files if possible,
by
dapsaille
-
Ormerod
Hello,
i get some problems with my two 0.3 nozzle (one is an original ormerod2 spare part 0.3 nozzle and another is an e3dv6 cheap clone).
Extrusion get stuck when i print .. the filament slip on the hobbed insert , too many pressure i presume
I use an homemade Styron abs 1.75 filament but i've tryed with a know to work commercial filament, same problem.
I've swapped the original pla extr
by
dapsaille
-
Ormerod
Thanks Treito,
Congratulations for your stl, they seems really nice, sadly i didn't find them before on thingiverse (crappy user interface i tought)
I cannot print so ... i've "ordered" a new aluminium bed and two legs.
now .. come the time of ... "waiting for delivery"
by
dapsaille
-
Ormerod
Hello,
a friend of mine can do some laser cut for me, i've asked him to laser cut the acrylics legs parts (i've broken them :x) and i'm looking for the dxf files for the bed support (polywood parts),
i've downloaded ormerod-master and ormerod-dev but i didn't find them,
do you know if they exists as dxf files ?
Thanks
Flo
by
dapsaille
-
Ormerod
merci à vous
je termine mon impression en cours et je m'occupe de régler cela dans slic3r
pour le skirt, en effet je connais ce principe mais ce n'est pas un soucis de skirt, bel et bien de décentrage.
Mourakami les réglages que tu m'annonces sont à faire tous les deux ou bien juste Slic3r fera l'affaire ?
by
dapsaille
-
RepRap Groupe d'Utilisateurs Francophone
Bonjour à tous.
j'ai un petit soucis de placement sur le bed avec Slic3r et mon Ormerod 2 .. je ne sais pas qui est responsable (surement moi ^^)
quand je veux imprimer cette pièce qui est bien large l'impression commence en dehors du bed par la gauche ...
pas de beaucoup (à la louche 5mm) mais suffisement pour que ça n'aille pas ...
le pire c'est que j'ai déjà réussi à imprimer cette pièc
by
dapsaille
-
RepRap Groupe d'Utilisateurs Francophone
thanks,
yes for now i use the stock ir probe.
by
dapsaille
-
Ormerod
Hello,
i use the fantastic DC42 firmware with my ormerod 2 but i encounter a simple problem ....
I'm calibrating the printer and i need to enter a G31 command ... but in the web interface i read Z-Probe value1 (value2) ...
which value use, the first or the second ?
Thanks
by
dapsaille
-
Ormerod