Dear RepRapers, I got a little Problem and I am asking you for help because I don't know what else to do... System I am using: Genereation 2 Electronics with Sanguino Bits from Bytes RepRap Version 2.0.1 Problem: The Extruder Motor doesn't work with the RepRap Host Software Things I tested: I checked all cables from the DC Motor Driver to the Extruder Motor - correct I checked all cables fromby Al3x - RepRap Host
thanks a lot!!! - I think I had a bit too much alcohol yesterday FYI interest - today is holiday in Germany Greetings Al3xby Al3x - Controllers
Hi There, I have a 204GT-1 Thermistor and need the right values to run the python script to get some calulated values. This is the Datasheet: Now I wanted to get the correct values out of this sheet: r0 = 200000;see datasheet t0 = 25; see datasheet beta = 4338; see datasheet r1 = ???; where do I get this value from r2 = ???; where do I get this value from num_temps = int(20); left this likeby Al3x - Controllers
Hi Professionals , I got a problem with the Thermistor (100K from RRRF) If it is hooked up to the Sanguino and not in fast cement just hanging in the air it gives me the room temp of 22 degree. Now I set up the heater with fast cement an put the thermistor is. It gives me 150 degree whts totally wrong. So I put it out of the fast cement ant values are correct again. I really checked that theby Al3x - Controllers
Hi there, thanks for your replies! I will give it a try.. Greetings from Germany Alexby Al3x - RepRap Host
Hi RepRapers, I am using the V.2.0.1 Kit from BitsfromBytes. Here is my Problem: If I press Home in the RepRap Host Software the Y-Axis Stepper turns in the "wrong direction" could you tell me where I can set the direction? Greetings Alexby Al3x - RepRap Host
Hi There, I got a small problem The thing is that I can't talk to my Sanguino if I boot up the Computer (WinXP at the moment). If I want to talk to it I have to reset the Sanguino bay pressing its butten. Afterwards I can use the RepRap Host Software, Do you have any hints for me to get this working correctly? Greetings from Germany Alexby Al3x - RepRap Host
I was wondering also... I am using those To find it out I blocked them with a piece of paper - and then I could drive them backward Greetings from Germany Alexby Al3x - RepRap Host
Hi There, I solved it by inverting the OptoEndstops in the Gcode Interpreter. Greetings Alexby Al3x - RepRap Host
Thans a lot for your replay. Maybe I have to add that I online have 3 Minimum Endstops on my Machine. I am using the V2.1 Endstops from the RRRF you mean I should check if if the software thinks that every axis is home because the Endstops give a 1 instead a 0? In which config file can I check? Greetings Alexby Al3x - RepRap Host
Hi experts, I got a problem moving the steppers with the RepRap Host software... First of all: - All electronics work and were checked with the demo code from make.rrrf.org - All electronics are connected correctly to the sanguino (checked min three times) - Connection between Sanguino and Host Software works Problems with the software concernign the steppers - I can only move the steppers inby Al3x - RepRap Host
So it was mi fault I forgot to put the comment away in ThermistorTable.h // Uncomment the next line if you are using a thermistor; leave it if you have a thermocouple #define USE_THERMISTOR Greetings Alexby Al3x - RepRap Host
thanks, I will check and post tomorrow again greetings alexby Al3x - RepRap Host
Hi bjathr, we've got the reprap software running on a intel essentials dual core atom board. No Problems! Greetings Alexby Al3x - RepRap Host
Hi experts just working at my RepRap machine - but struggeling with a problem. I am using the Temperatur Sensore 1.1 (http://reprap.org/bin/view/Main/Temperature_Sensor_1_1) If I fire up the RepRap Software it shows me sth about 400 degree... kind of wrong (no power on the nichrome wire) I didn't change the Gcode Interpreter source ?!? Do you have any hints for me? Best Regards from Germaby Al3x - RepRap Host
Thanks for your reply! I got It working now: Software: Arduino 0013 GCode_Interpreter Sanguino Software Here is the fix parameters.h add "typedef uint8_t byte;" to the top \GCode_Interpreter\process_string.pde change word to word_old Line 7 : char word_old; Line 101 : word_old = c; Line 115 : word_old = 0; Line 118 : process_string(word_old, serial_count); This should do it! Bestby Al3x - RepRap Host
Hi There, I got a problem with compiling the Gcode Interpreter. Here are my software specs: - Arduino 0012 Alpha - Sanguino Software 1.4 I integrated the Sanguino Software and it works - I can upload files to the Sanguino! Now I downloaded the latest Gcode interpreter files from here: I followed the instructions from here: But If I try to compile I get an error: C:\DOKUME~1\Laptop\Lby Al3x - RepRap Host
Thanks Corwin! I will give it a try with >>> Port(name)=COM3 Alexby Al3x - RepRap Host
Hi there, perhaps you can help me with my problem with the RepRap Software. But first to the System: - Sanguino - USB to TTL calble --> listet as COM3 in WinXP - Intel Atom board - WinXP pro SP2 Software: - Latest JRE V 6U12 - sanguino-software-1.4-r1 - reprap-host-windows-20081218 - arduino-0013-win - Connection and upload with the Arduino Software works! If I try to boot up the RepRapby Al3x - RepRap Host