Hi guys I have HyperCube and when I try to print circle my printer print oval shape not circle Any idea ?by Vido - CoreXY Machines
Hi guys and girls I have BTT SKR 1.4 Turbo and it keeps entering in main menu and buck to Info Screen on its own on my LCD Rep Rap Smart Controller, so I disconnected the EXP 1 on MCU board jack and measured pin 2 and GND on MCU board and I'm reading 1.45 v, any idea tnx ?by Vido - Tech-Talk
Quotekf2qd input pulled high? input pulled Low? Does you input require and external pull up/pull down? I tired to enable/disable pull high/low in marlin but same dealby Vido - Firmware - Marlin
Hi guys, I have BTT SKR V1.4 TURBO and I cant figure out why my PNP inductive sensor does not work when plugged in to z_min ? It works as expected when connected to y_min or x_min ?by Vido - Firmware - Marlin
Obradovah se kad sam vidio da postoji forum za naš region ali ga (na žalost) niko ne posjećuje možda zato što svi kupe gotov kit poput anet A8 odrade par štampi i to je to nema samogradnje i tinkeringa toga nam treba više pozdravby Vido - Serbia, Belgrade, RepRap User Group
Hi guys I'm planning to build Texh2C Hyper Cube CoreXY printer and use ReArm board with good old RAMPS 1.6 and run them with 24v so I have some concerns. First is with my heat bed I found few on aliexpress dimesion 210x210 mm rated at 12/24v but they do not have resistors and LED's soldered on them so I need to buy those separately, but I don't know which SMD type and how big resistor do I needby Vido - General
Hi guys, recently I came across this video it shows how to mesure delta z hight with micrometer and with help of OpenDACT adjust accuracy of delta printer within 0.015mm to print bed.It only works with repetier (for now). I started issue on Marlin github page and also ther is some progress on OpenDACT gut hub page to make it work with any Delta 3d printerby Vido - Delta Machines
Quotedc42 Here's a video of an easier way that only works with RepRapFirmware: Right, so I did not know that IR works on glass or does it probe surface under the glass ? But thanks for sharing and I assume that this printer is yours so where did you obtain this sensor ? Tnxby Vido - Delta Machines
I know that thread is old but if you would like to really calibrate delta check this video sadly it only works on repetier but hope for nowby Vido - Delta Machines
I like what Im seeing but I did not read anything about delta arms so here is my proposal. You should use this you already have mounting points for carriage just order custom arms and a must magnetic ballsby Vido - Delta Machines
I will stick with Marlin because Im sure that people who develop it will do even better job with 32-bit version, I cant wait for proper Re-Arm boardby Vido - General
Quotefrankvdh This method relies on measuring the resistance between nozzle and a metal bed... when it's zero, the nozzle is touching. If your printer has a metal structure, the nozzle may already be electrically connected to the bed, so it will always read zero. Thank you for nice explanation my heat bed is separated from printer frame they do not have any conductivity between them Quotefrankvdhby Vido - Firmware - Marlin
I dont see why sprint and switch and needed Im thinking just using nozzle and aluminum bed as switch, the nozzle is touching the bed so there is your perfect switch its at zero height its not needed anything just implement it in code and let users decide will they gone use it. But tnx for quick replay cheersby Vido - Firmware - Marlin
I saw some printer on ali which use nozzle to touch heated bed in order to do autoleveling so I hew few questions How safe is this moving speed while touching bed is very slow ? Is this feature implemented in Marlin, can I install newest firmware and do same autoleveling in genuine marlin ?by Vido - Firmware - Marlin