Show all posts by user
Printing issues ...
Page 1 of 1 Pages: 1
Results 1 — 12 of 12
Thanks for your response,
1) yes. I am using Bowden type arrangment using silicon tube. Now I have kept my retraction at 6.5 mm as default in cura and retraction speed increased from 25 mm/s to 40mm/s. Still I observed some blobs/zits intermittently/randomly on the wall of printed part. Should I increase retraction speed further?
2) yes. I tried to give prints directly from SD card inserted but
by
pvishup19
-
Printing
Please respond me!
1)I am printing lithophanes, I increased my retraction from 6.5 mm to 7.5 mm still little zits/blobs can be seen on the surface of lithophanes.
2) I am using pronterface for printing, My printer gets slow down at some layers while printing . When it's slow downs, I just click the button of mouse randomly on pronterface interface then printing speed becomes normal. I don't thi
by
pvishup19
-
Printing
Please respond me!
1)I am printing lithophanes, I increased my retraction from 6.5 mm to 7.5 mm still little zits/blobs can be seen on the surface of lithophanes.
2) I am using pronterface for printing, My printer gets slow down at some layers while printing . When it's slow downs, I just click the button of mouse randomly on pronterface interface then printing speed becomes normal. I don't t
by
pvishup19
-
Printing
I am printing lithophanes, so how can I adjust mesh size in that ?
Kindly respond
by
pvishup19
-
Printing
Sorry but I haven't got you completely
1) what do you mean by stupidly detailed ? How to reduce mesh size.
2) I am using hotend cooling fan as well as part colling fan. Part colling fan duct is just 5-10 mm away from nozzle. And hotend colling fan lies on the hotend fins.
by
pvishup19
-
Printing
I am using hypercube 3d printer, 12v SMPS , BTT SKR V1.4 motherboard along with A4988 stepper driver and nema 17 motors.
Currently I am facing following two issues:
1) while printing, my printer gets slowdown arbitrary at many places and in those layers, material get diposit more, and several blob appears.
What is the reason for slowing down the nozzle while printing and what shall I do?
2)
by
pvishup19
-
Printing
I am using 12v SMPS power supply and MOSFET for heating my heatbed.
1) without using MOSFET , my heatbed was not able to heat up
2) now I am using MOSFET, and now after 5-10 min my heatbed heats upto 25-28 Degree Celsius. After that it beeps and gives heating error.
What could be the reason for this? What shall I do now?
by
pvishup19
-
Printing
I didn't understand your response regarding endstops.
Problem is not related to , endstops are not getting triggered while homing.
Actually, When my object hits the endstops while homing, even then my headbed don't stops.
Is this related to ENDSTOP_NOISE_THRESHOLD ?
by
pvishup19
-
Printing
1 ) Yes I tested my endstops using M119 and they are working properly.
a) when they are not triggered all endstops shows "OPEN" status
b) when I triggered manually by inserting object into optical endstops and proximity sensor they shows "TRIGGERED" status. But even if they are in triggered mode, my nozzle moves and it is not stopping.
2) Regarding my second issue , please find the attached snap
by
pvishup19
-
Printing
1) I am using hypercube 3d printer, BTT SKR V1.4 motherboard along with A4988 stepper driver and nema 17 motors.
For sensors , I am using optical endstops for x and y axis, proximity sensor in z axis.
I have not enabled sensorless homing in my Marlin configuration. Still printer homes at imaginary points and it is not stopping whenever printer hits the sensors.
2) I am using reprap discount full
by
pvishup19
-
Reprappers
Is there anyone? Kindly address my issue. Waiting for your response.
Thank you.
by
pvishup19
-
Printing
1) I am using hypercube 3d printer, BTT SKR V1.4 motherboard along with A4988 stepper driver and nema 17 motors.
For sensors , I am using optical endstops for x and y axis, proximity sensor in z axis.
I have not enabled sensorless homing in my Marlin configuration. Still printer homes at imaginary points and it is not stopping whenever printer hits the sensors.
2) I am using reprap discount
by
pvishup19
-
Printing