Show all posts by user
Page 1 of 1 Pages: 1
Results 1 — 23 of 23
Thx DC. Do i need to change to 32 bit now.?Headscratching!?
Of course I know the advantages but atm iam happy with y ramps 1.4. Tough i didnt knowed that the firmware for 32 bit boards are more developed.
I putted in these values in the repetier configurator but maybe i missed the res. @ 25° thing as my hotend res. differs from the bed at room temp. Ill check it.
Is it just the resistance of
by
amicado
-
Firmware - mainstream and related support
Get the following error downloading the firmware with 0.92 configurator even if i dont change anything in the configuration. In the old firmware no error occures, without modification just plain new downloaded with the inserted configuration.h from the working firmware. was there anything changed in the ui.cpp?
by
amicado
-
Repetier
Thx again repetier you opened my eyes a little!
I have not considered the case of a failure, and you are totaly right that my schematic would pull up the heater mosfet and enable the heater!!
Tough i have a relay controlled by inverted ps_on pin (positive triggered) by which in this case would open up and disable the 12V supply its a bad practise i guess, and i should change that right?
Ive de
by
amicado
-
Repetier
I have the issue, that i assigned one of the servo pins as the heated bed pin to free up the D8-D10 ports for fans.
How can i invert the signal of just the D11 pin where the heated bed control is wired.
As i saw there is a invert heaters function, but that would also invert the extruder heater signals i guess.
i need just to invert the D11 pin.
Regards, Alex
by
amicado
-
Repetier
QuoteOk, I found the reason.
DUDE YOU ARE THE BEST!
I thought exactly the same when i looked over the schematic to double check the pinout.
The question is still why would that be of use to access this pins on the ramps board?
I guess its not possible to change the two pins separately to digital pins if they are used for the communication. (USB communication? They look like USART pins thou)
by
amicado
-
Repetier
Shame on me but there is some misbehaviour of the display itself! Maybe this is causing the trouble
Look @
How can i fix this?
by
amicado
-
Repetier
@ justcurious:
i did the pin assignment now in config.h as it should be, and left the two lines
Quote// #define RAMPS_V_1_3
// #define RAMPS_V_1_0
commented. Thats not the point. regards
by
amicado
-
Repetier
here u go, watch with sound
by
amicado
-
Repetier
here u go, watch with sound
by
amicado
-
Software
Oh sry my mistake! The CASE_LIGHTS_PIN gets defined in configuration.h^^
The problem persists...
if i select pin 0 or pin 1 in config.h for CASE_LIGHTS_PIN no toggeling.
ill upload a video now, because i feel like iam dumb, but ill like to show you that it doesnt work...
by
amicado
-
Repetier
#if CASE_LIGHTS_PIN >= 0
SET_OUTPUT(CASE_LIGHTS_PIN);
WRITE(CASE_LIGHTS_PIN, CASE_LIGHT_DEFAULT_ON);
#endif // CASE_LIGHTS_PIN
btw i cant find this code fragment in 0.92. in which file should that be?
in ui.cpp i have:
#if CASE_LIGHTS_PIN > 0
case UI_ACTION_LIGHTS_ONOFF:
TOGGLE(CASE_LIGHTS_PIN);
UI_STATUS(UI_TEXT_LIGHTS_ONOFF);
break;
by
amicado
-
Repetier
Iam sorry to bother you, i dig depper now^^
If i select Ramps 1.3/Ramps 1.4 and Arduino Mega in the configurator (0.92) i get a pins.h with the following code:
Look at the 2 highlighted lines. Shouldnt get the first uncommented by default to assign a ramps 1.3/1.4 board?
Second there is no CASE_LIGHTS_PIN assigned to a port number by default by the configurator tool (I searched the whole pins.
by
amicado
-
Repetier
QuoteSeems to be a simple case.
unfortunately not
If I change it for both files (uimenu.h & ui.cpp (i guess you meant ui.cpp not ui.h)) with the >=0 sign instead of just >0 i do get the menu entry even if i assign digital 0 output (is it the one on AUX1? 0,1,GND, VCC)
but the button press doesnt toggle the light off or on.. it always stays at "ON"...
even if PIN 1 is assigned, (wher
by
amicado
-
Repetier
Ok, i got a little bit further!
When i assign another pin then the digital 0 pin it works!
I get a menue entry for switching light on and off and i can switch it on and off. (0V / 5 V)
It only doesnt work when digital 0 is assigned. It doesnt matter if its firmware 0.91 or 0.92. Its not working in both.
Does anyone out there has an explanation for that? Maybe repetier himself can dial in here
by
amicado
-
Repetier
I try to implement a case light but failed because of following behaviour:
In Configurator, when i say case light pin = digital 0
i dont get a menu entry on my reprapdiscount full grafic controller, maybe because of the following line in the uiconfig.h:
#if CASE_LIGHTS_PIN > 0
UI_MENU_ACTIONCOMMAND(ui_menu_toggle_light,UI_TEXT_LIGHTS_ONOFF,UI_ACTION_LIGHTS_ONOFF)
#define UI_TOOGLE_LIGHT_ENT
by
amicado
-
Repetier
Ja genau das Gebäude mein ich Das mit der Kugel an einem Pendel^^
hab ich auch überlegt, unten hohe dämpfende Füße!
Dämpft, und macht Platz das Netzteil vielleicht doch unten zu montieren...
by
amicado
-
Mechanik
Hey, voll cool! War das für eine Laseranwendung?
An sowas in der Art mit den Gummidämpfern hab ich auch gedacht. Gibt ja auch dieses Gummifilament, da könnt ich mir schon was drucken.
Nur wäre halt interessant, da ja bei Dir die Nutzlast auf der "Masse" (Granitplatte) geruht hat ist ja klar dass die dann gedämpft wird.
Nur wie siehts aus wenn die Masse über den langen Hebel der Achsen oben au
by
amicado
-
Mechanik
Aus der Not heraus, dass mein Netzteil nicht in den Fuss meines gerade in bau befindlichen Cherry Pi III delta druckers passen wird habe ich überlegt es oben auf zu montieren.
Irgendwo hab ich aber gelesen, dass dies eine Masse darstellt die sich aufschwingen kann, was ich ja nicht möchte zwecks druckqualität.
Jetzt würd ich gern wissen ob sich dies auch positiv nutzen liesse wie bei einem erdbe
by
amicado
-
Mechanik
Sieht echt nach einem retract problem aus, da es in x und y achse auftritt.
Sonst fällt mir da nur ein verkanten der düse ein, solle diese eine scharfe geometrie haben. Keine ahnung wie diese bei deinem Printer aussieht.
Aber die Kunststoffäden zwischen den Leerwegen deuten eher auf retract hin.
by
amicado
-
Software
Jungs Ihr seid klasse! Es war tatsächlich die Temperatur...
Jetzt mit Duckted Fan und 200° (PLA Schwarz, 3Dee) am Hotend -> Keine Knackser, Keine Aussetzer
Lg Alex B.
by
amicado
-
Extruder, Hotends & verschiedene Materialien
Danke Wolfgang für die schnelle Antwort!
Klar war ich schon mal höher, aber dann tritt genau das ein was du meinst. Die kühlung reicht nicht aus, die V2A Heat barriere wird zu heiss, und das PLA schmilzt zu früh und jammed garantiert.
Ich druck aber gerade wie im Video vielleicht gesehen einen ducted fan für den hotendkühler. Dann sollte das kein problem mehr sein, zumal jetzt gerade mal ein fa
by
amicado
-
Extruder, Hotends & verschiedene Materialien
Hallo liebe Reprapper!
Hab einen repstrap mit einem Wade Extruder (greg universal).
Pla 190°. Selbst gedrehtes Hotend (Vollmetall) ala E3D bauweise.
Selbst gerändelte Filamentschraube. Alles tuto bene kalibriert auch den Extruder von den Schritten her. Bei manuellem Vorschub passt die extrudierte Länge... Drucke sehen gut aus, und sind auch masshaltig.
Jetzt zum Problem:
Des öfteren höre ich
by
amicado
-
Extruder, Hotends & verschiedene Materialien