Show all posts by user
Page 1 of 1 Pages: 1
Results 1 — 20 of 20
Ok! Thanks again, will try that now!
by
Darki
-
Repetier
Thanks!
Can I use the online configurator to download this?
by
Darki
-
Repetier
Hi!
I just want to know if i can use firmware retraction in slic3r!? Whats the advantage? What do I have to set up in the firmware to use it?
I am using repetier firmware, the newest Version.
Thanks!
by
Darki
-
Repetier
I was able to get the error again! Same part as yesterday. Stopped 2 or 3 layers under that one from yesterday.
Debug gave me:
02:58:52.203 : Buf. Read Idx:1 Buf. Write Idx:1 Comment:0 Buf. Len:0 Wait resend:-1 Recv. Write Pos:0
02:58:52.203 : Min. XY Speed:4.74 Min. Z Speed:4.74 Buffer:0 Lines pos:15 Write Pos:15
02:58:52.203 : Wait loop:1
I was recording and standing enarby, but I couldn't s
by
Darki
-
Repetier
I'm now printing with (improved) bad :-) cable routing, camera and I'll try to get that debug-message.
For me, the error is definately not related to printing-time, printing-steps or size.
Also no luck with usb-charger.
by
Darki
-
Repetier
@repetier
Sorry, but what do I have to do to get the debug message?
Your idea is great! Errors should be displayed until the user does something.
@ brekel
I'll also try to make it even worse by twisting the cables!
by
Darki
-
Repetier
Ok! If there is a message on the display, I'll do another print with my camera.
So your advice is to print from sd card and if it stops, I have to connect it to repetier-host without reset, right!? How do I get the last messages? I guess the message will be sent only once!? How can I see the state?
by
Darki
-
Repetier
I didn't get your last point. Could you explain it a little further?
I can randomly reproduce it, but I can't log it, therefore I asked if it is possible to write a log to the SD-card. If I do a large print (4 hours above), I think its almost sure that there will be an error.
The only things I can try now is:
- shorten the cables to the display
- try another sd-card
- separate the cables even m
by
Darki
-
Repetier
Ok! Wie gesagt, benutz am besten kein mechanisches Relais!
Zurück zu dem Problem oben:
Hat jemand eine Idee? Das Problem ist, wenn ich von SD-Karte drucke und auf dem PC logge, tritt kein Fehler auf. Wenn ich aber die USB-Verbindung trenne und von SD-Karte drucke, habe ich den Fehler. :-/
by
Darki
-
Software
Hi!
Tried it myself because I thought it had something to do with the power supply. Still stopping.
@repetier:
I tried to log it as I told you above. Had a 2 hour and a 6 hour print from SD-card with logging to my PC. Guess what, no error/stopping. The camera was recording all the time. Hab another short print in the night with no connection to the PC (not logging, not recording) as I did befo
by
Darki
-
Repetier
Nimm die "dead time control" und beobachte vorher, wie lange es dauert, bis vom Einschalten des Heizbetts (bei der Wunschtemperatur) sich eine Temperaturerhöhung zeigt. Den Wert trägst du dann dort ein. Es kann allerdings sein, dass das mechanische Relais damit nicht klarkommt. Solltest früher oder später auf ein Solid-Relais gehen.
Ich habe es auch so eingestellt und bei mir ist der Temperaturbe
by
Darki
-
Software
Hi Brekel,
try to connect a USB-cable from the microcontroller to a USB-charger. I think it could have sth to do with power supply.
by
Darki
-
Repetier
Super!
Leider ist das bei mir/uns ein anderes Problem. Er druckt ja und auch wenn es 20 identische Layer übereinander sind, bleibt er stehen.
Momentan läuft ein 6h Druck mit Logging, mal sehen was rauskommt.
Edit: @Kurt: mach mal folgendes: Druck mal von SD-Karte ohne den rechner dran zu hängen, mach aber ein USB-Kabel dran und das Kabel in ein USB-Ladegerät.
Edit2: hab gerade gelesen, du hast
by
Darki
-
Software
Well, I just finished a 3 hour print with no complications. (It failed last time) I downloaded the new Firmware with my settings, changed nothing except for the "debug_print". I was logging and recording all the time. :-/
I wouldn't say that the problem is gone... I've got another 5 or 6 hour print for tomorrow!
Is there any way I can log something on sd-card? (for the case that the usb connectio
by
Darki
-
Repetier
Hallo Kurt.
Ich betreibe es mit der "dead time control". Aber das mit den Impulsen ist natürlich eine gute Idee. Ich habe zwar kein mechanisches Relais, sondern ein Solid-Relais, aber durch das schnelle Einschalten können natürlich Spitzen entstehen. Ich fahre gerade einen Druck mit Logging. Denke da müsste man es erkennen können.
Ich konnte aber deinem Beispiel nicht ganz folgen. Ich weiß nicht
by
Darki
-
Software
Ich drucke immer nur von SD, weil ich festgestellt habe, dass der Drucker die Daten vom PC nicht schnell genug nachläd und den Puffer leert. Selbst von SD sieht man manchmal, dass der Puffer von 16 auf 5 oder so runtergeht (aber nicht pausiert).
by
Darki
-
Software
Quoterepetier
First you should find out what kind of hang you have. As you know th eline where it happened, you were not printing from sd card. In that case it might wait for a "ok" to receive so buffers get empty. That should only happen if you have communication errors happening.
Surely I was printing from SD-Card. I started the print through the menu on the lcd! And the controller isn't even
by
Darki
-
Repetier
Hi community,
I've got a problem here. I print from a SD-card and my printer just stops somewhere in the print. This happens all 2 to 4 prints. "It stops" means, that the printer stops moving, the display tells me "ready", the heated bed and the extruder-heater stay on. I'm almost sure that the controller does not reset itself because the heaters stay on and the displayed position is correct. It
by
Darki
-
Repetier
Bei mir ist es anders. Wie gesagt, er bleibt zwischendrin stehen, ganz zufällig, und ich gehe davon aus, dass es kein Reset ist, weil alles an bleibt.
EDIT: ...weil alles an bleibt, und die Position auch weiterhin richtig angezeigt wird.
by
Darki
-
Software
Hallo Community,
ich habe folgendes Problem. Ich drucke mit meinem Drucker von SD-Karte und alle 3 oder 4 Drucke (bei Drucken ab 2 oder 3h auch etwa alle 2 Drucke), unterbricht der Drucker einfach. D.h. konkret: er bleibt stehen, auf dem Display steht "bereit", die Heizelemente, Platte und Extruder, bleiben an. Ich gehe davon aus, dass sich der Controller nicht neustartet, denn dann wären die He
by
Darki
-
Software