Show all posts by user
Un gros plateau (8mm) fixe à la base de la machine
(comme si on reprenais le XY de la Mondrian mais qu'en plus il bouge en Z)
En fait ça fait suite à la Fête de la Science il y a 2 ans ptet, on avait construit au fablab une reprap de 1000x700x1000mm sur le principe de la Mondrian, et on s'est vite rendu compte que à cette taille faire bouger le plateau en Z n'était pas la meilleur solution. Mie
by
Emmanuel
-
RepRap Groupe d'Utilisateurs Francophone
Après la FoldaRap et la Mondrian viendra bientôt l'Alto, une architecture plus adaptée pour construire des machines de grande taille ^^
Mais justement, comme j'utilise pas un soft paramétrique (sketchup powa), pour chaque dimension il faut redessiner/étirer les plaques découpées.
Du coup ma question (histoire de ne pas avoir dix milles fichiers) : quelle tailles vous semblent le plus intéressa
by
Emmanuel
-
RepRap Groupe d'Utilisateurs Francophone
Iyo !
Je publie l'info également ici comme ça en intéressera sans doute quelques-un : la dernière version stable de la FoldaRap vient d'être publié sur ^^
Dans les améliorations :
* extrudeur 3-4x plus puissant (nema17 à la place du petit nema14)
* montage légèrement simplifié (pieds identiques, plaque arrière côté prise)
* implémentation de plusieurs contributions de la communauté, parmi le
by
Emmanuel
-
RepRap Groupe d'Utilisateurs Francophone
(note : the "2.2" was an interemediate version, using the printed parts of the 2.1 with the nema17 extruder and few little things, as the printed part could accomodate both nema 14 and 17)
by
Emmanuel
-
FoldaRap
Here is now the latest stable version of our little FoldaRap
Here are the main following improvements :
* replacing the extruder nema14 by a nema17, having 3-4x time more torque
* slightly simpler assembly (same feet on front and rear side, adding a rear plate for the plug/switch, etc.)
* implementing several contributions from the community, like the nut-holder to adjust the bed (Damien) or th
by
Emmanuel
-
FoldaRap
Merci pour ton retour, a la description de la vibration j'aurais pensé aussi aux fils
by
Emmanuel
-
FoldaRap
Hi Xoan !
Nice to know that you are going to build a Mondrian
1) depending on motors the screw hole is more or less deep, ours are just enough to hold the screw but 0.5mm maybe, using washer as spacers is a good idea
2) in fact the screws are used to adjust the play, like the four grubscrew for the other direction
by
Emmanuel
-
FoldaRap
A priori il n'y a pas de différence de montage suffisante entre la 2.1 et la 2.2 pour que toute la doc soit refaite, on a adapté les sections (par exemple le bloc tête chauffante)
Tandis que pour la 2.5 qui arrive là c'est tout l'ordre de montage qui est revu (et où du coup faut refaire plein plein de photos...)
by
Emmanuel
-
FoldaRap
That's right !
It's the same, and instead of placing the power switch in the previous "rear foot right" it's in a acrylic panel added between the front feet (or maybe we could say at the rear of the machine now).
by
Emmanuel
-
FoldaRap
In fact the bolt is screwed in the plastic, either by the top (it allow an easier adjustement on the fly), or by the bottom (it may be easier to screw it in if the z-slider is already on the foldarap)
by
Emmanuel
-
FoldaRap
This idea was recently revived for the Mondrian3 (being a little too huge for a bowden), the files are here for those who want to play with it :
by
Emmanuel
-
FoldaRap
At this moment it was the pulley that was taking the load (on the printed part), it worked but needed a well adjusted tightening to turn smoothly while having no play in Z.
It was redesigned few weeks ago to use two bearings, but this time the assembly is simpler as the pulley is inserted in force between the two bearings.
(the downside is that the printed parts need to be designed for the pulle
by
Emmanuel
-
FoldaRap
Ah ben c'est encore mieux alors
by
Emmanuel
-
FoldaRap
Pour les plus avant-gardiste, la FoldaRap est supportée à présent dans le slicer IceSL :
Il faut une grosse config pour le faire tourner mais ça intéressera peut-être certains de jouer avec
(ps : I'm back ! Je vois qu'il y a plein de posts à rattraper mais comme j'arrête de m'occuper du fablab de l'école où je travaillais ça va me laisser plus de temps pour trainer de nouveau sur le fofo et
by
Emmanuel
-
FoldaRap
It should work, as repsnapper will just stream the Gcode to the board, and marlin or other firmware should interpret it normally as it's mostly G1 moves (I guess, from my experience where we used a small cnc with a Sanguinololu and gcode from pycam)
by
Emmanuel
-
RepSnapper
hmm sinon toutes les thermistances utilisées jusque là sont des 100kOhm
quelque chose qui pourrait peut-être provoquer un tel écart, dans le firmware au niveau du choix des sondes de température tu avait bien choisi 1 ou 7 ?
(1 correspond à une table pour sonde 100k, la 7 plus précisement au modèle utilisé)
(autrement j'allais dire dommage car la carte était déjà chargé avec une version de Marli
by
Emmanuel
-
FoldaRap
Hello Glenn,
Comme dit dans le mail, et comme vous l'avez déduit ici c'est les pièces imprimées qui ne sont pas aux bonnes dimensions
La solution de Pascal pourrait sans doute fonctionner, ça ferait enlever 0.5mm vers l'extérieur aux quatre trous
(si ça peut aider les ouvertures carré au niveau de la zone qui retient la barre dans les pièces imprimées est prévue pour passer un serre-cable et r
by
Emmanuel
-
FoldaRap
Cool !
With the current development in Italy and France the wiki will need to be re-organized to show all the options that modularity allow to choose from
by
Emmanuel
-
FoldaRap
that's clever
by
Emmanuel
-
General
Sorry for the remaining picture of a previous build, as you may have noticed all the endstops are wired as "normally closed" (the middle pin is not used)
You can always invert the logic of the endstop in the firmware if needed, but I've just updated that part of the wiki to avoid confusion
by
Emmanuel
-
FoldaRap
c'est "Marlin_FoldaRap2_Minitronics"
le premier est pour la folda1
le troisème est pour la version avec pignon-crémaillère imprimées (où il n'y a pas de grand changement si ce n'est la direction de l'axe X et la valeur en pas-par-mm)
by
Emmanuel
-
FoldaRap
05-mar
Nancy-Paris
By train, metro
Then at the FacLab
by
Emmanuel
-
FoldaRap
06-fev
Nancy-PontàMousson
By car
21-fev
Nancy-Nancy
By car
by
Emmanuel
-
FoldaRap
Hmm curieux,
Les lignes
T:199.0 E:0 W:9
T:199.0 E:0 W:8
T:198.5 E:0 W:7
T:197.8 E:0 W:6
T:197.2 E:0 W:5
T:196.7 E:0 W:4
T:196.7 E:0 W:3
T:197.0 E:0 W:2
T:197.7 E:0 W:1
T:198.6 E:0 W:0
.k T:201.3 /200.0 B:0.0 /0.0 @:127 B@:0
me font penser à quand on règle la température dans Slic3r (filament settings), et qu'il attend que la température soit au point avant de se lancer
parfois ça ne se lance
by
Emmanuel
-
FoldaRap
Thanks for sharing, it's always interesting to see
gmh39, your drawing could be possible, if you add panels on the frame (wood, acrylic, etc) you can remove one Y extrusion of the frame
by
Emmanuel
-
FoldaRap
One of the reasons for the moving motors was to make it more modular and to shorten the lenght of the belt, as this design is intented to be scaled up easily, and ultimately replacing belts by printed rack&pinion
But both solutions are working fine
by
Emmanuel
-
FoldaRap
Hi Conoral11
I was using 14N.cm motors previously (from Zappautomation or Ldo-motors).
The motors you pointed at are ok, you can have them also directly from their website "robotdigg", just add in the comment that you want 1.25A (300rpm) for the movements, the 0.8A (100rpm) is better suited for an extruder.
by
Emmanuel
-
FoldaRap
yeah he told me he was crazy busy and had some time recently to update his github repo ^^
I'll have a try at nema 17 too, it will certainly help on bigger sized machines
by
Emmanuel
-
FoldaRap