I used the interface until it was very sluggish and then looked at task manager The only cpu usage was chrome at a steady 15% nothing else was running any cpu time Rob Hby bobexuk - Ormerod
I run windows 10 on a machine with a very fast processor and loads of memory I run chrome with only the web interface open I have used firefox and had the same problem Rob Hby bobexuk - Ormerod
Hi all I use a duet 0.85 with my Ormerod 2 and have had to do a lot of troubleshooting - various mild problems. I use Chrome and the web interface latest version with the latest DC42 firmware {thank you for continuing this development) Initially at start-up the response of my machine is almost instant but as I send more and more instructions to check homing etc the machine becomes sluggish Eventuby bobexuk - Ormerod
Hi all I am rebuilding my Ormerod to the improved version 2 with larger 200 x 300 bed and added height on z axis(10cms) I like the belt gripping on the Y carriage and the x carriage bearing running under the x arm I did have problems with the belt grip on the x carriage but it worked well eventually I am using a duet 0.85 in my rebuild and here is where my problems start I can sort out the chanby bobexuk - Ormerod
Fixed I loaded Dc42's 1.09k firmware and web control to match and file upload works fine Is this a bug in the most recent firmware or web control? Rob Hby bobexuk - Ormerod
hi I am running latest DC42 firmware and matching web control. I can upload small gcode files and print them using web interface Large gcode files freeze at 100% and if I close the file I get an error . I have reset the duet and tried all types and sizes of sd card with chrome and internet explorer. What am I missing in my setup? Rob Hby bobexuk - Ormerod
Hi I have had this problem- the solution was to gently heat the block with a blow torch and the cartridge literally fell out Hope this helps Bob Hby bobexuk - Ormerod
Hi the pads are as per your picture the screens work fine on 3.3volts I do not want to risk it at 5volts regards Bob H ps will you be enabling the rotary control in your firmware as I already have fitted them to my boardby bobexuk - Ormerod
hi I looked up spec from ITEAD web site will look at pcb when I can later today regards Bobby bobexuk - Ormerod
Hi my itead Lcd s have arrived and they are 3.3volt not 5 volt luckily I had not changed the jumper from trying another lcd I had just be careful about the voltage selection regards Bobby bobexuk - Ormerod
Hi I think I have dyslexia as far as connections go wiring was wrong now all works fine but one lcd is dead swapped out the paneldue and altenate lcd work fine Anyone designed an enclosure for this my cad abilities are worse than my reading wiring so cannot design my own Bob Hby bobexuk - Ormerod
Hi my panel due has arrived and lights up one of my lcd the other lcd is dead - cause unknowm I can see both paneldues on windows when connected by usb and screen works on both When I connect to duet neither board lights up my working lcd disconnect and try usb and all works what am I missing Bob Hby bobexuk - Ormerod
Hi I am using the duet board on a reprappro mendel This is great success - no more bed levelling using Dc42s hotend the only mods were to reverse the extrude stepper motor and extend the x axis micro switch mounting I would recommend this change in controller to anyone using a reprappro mendel regards Bob Hby bobexuk - General Mendel Topics
Hi I am using the duet board on a reprappro mendel This is great success - no more bed levelling using Dc42s hotend the only mods were to reverse the extrude stepper motor and extend the x axis micro switch mounting regards Bob H Sorry posted on wrong forumby bobexuk - Ormerod
I will put this on mendel forum I have a reprappro mendel with vertical x axis rods The mounting for the hot end is the same as the ormerod so no mods needed the only mod was to extend the x axis micro switch and reverse the extruder stepper Bob Hby bobexuk - Ormerod
doh forgot about mac address thanks for the help will try it asap the mendel with duet and dc42 hot end is working really well otherwise Bob hby bobexuk - Ormerod
Hi all I have set up my mendel with a duet controller using DC42s hot end This works very well but if I run my ormerod at the same time the mendel keeps dropping the connection to chrome The duets are on separate ip addresses and run without a hiccup on their own what is causing this clash? Bob Hby bobexuk - Ormerod
Hi all sorted I think - turns out it was a utility called Netgear Genie which they supply free to monitor the network. It records all new devices on the LAN as they connect - it appears to send out the request which produces the error. I have removed it and now the error messages has gone (I hope) Bob Hiamby bobexuk - Ormerod
Hi you may be correct re an addon I have now found a report by some one who had the same error report They had installed a netgear D6300 - I have also just installed the same router!! Now to do further research - it looks as if my new router is the cause> Bob Hiamby bobexuk - Ormerod
Hi all I have an ormerod 1 with dc42 hot end.Firmware 0.78za-dc42 Web control 1.03 Every now and then (approx every two minutes) I get the error in the message title I have checked everything and can see no cause for this- can anyone help? Have tried several sd cards rewritten them and also used several pcs - all with same problem - i also have several duet cards with same firmware and web controby bobexuk - Ormerod
Hi all I have several questions 1 please see attached photo why do the first few layers in all my prints appear ragged - all of the prints show this reproducible raggedness. 2 do I need to calibrate for pla and abs separately to allow for the greater contraction of abs? Thanks Bob Hby bobexuk - General Mendel Topics