but to do that and have a correct reading I need to remove the thermoresistor from the hotend and put it directly in contact with the bed (preferibly with a piece of kapton to fix it to the bed surface... and also disconnect the fan) right?by Zonzo - Ormerod
QuoteKimBrown Hi Zonzo, I think your extruder temp is higher than you think my friend. Maybe you can measure it to find out. Sometimes the thermistors are not reading correctly. Also with the Retraction set to 4mm, increase the speed... I see you are using:- retract_speed = 30 Increase this to 45... I see you are trying to reduce BackWash from the Fan.... Try my Duct as it will work better. Kim.by Zonzo - Ormerod
Quotedc42 A few more suggestions: Thanks for your help, really appreciated!!! Quotedc42 1. I think you are probably extruding at too high a temperature. I use 195C first layer and 190C for the rest. I usually extrude at 185° for all the layer (too low? it look easy to extrude...) Quotedc42 2. Have you increased retraction in the slic3r settings to 4mm yet? The retraction was one of my first chaby Zonzo - Ormerod
Quotedc42 1. Check whether your G30 setbed parameters are still correct, preferably when the bed is at operating temperature. If you find the z-height at all unstable, then reinforce the MDF bed support, or replace it with aluminium (there are a few threads about this). 2. Remove the M111 S1 command from config.g. It slows down direct printing, and it's only needed when debugging. 3. Increase tby Zonzo - Ormerod
Hi everybody, I need your help!!! I'm unable to have progress... so step by step, what I need to do?? Actually I've assembled my printer run the ormaxys.g create the setbed file (as show at the end) and printed a few pieces to improve the ormerod (y axys belt tensioner - z axys new nut - airduct), but overall I am not satisfied with the result of printing. then I want to start over, what shouby Zonzo - Ormerod
Ok, thanks Cash & Stevelup my fault! the setting was the original... thanks for the hint about edit profile_0by Zonzo - Ormerod
ok, I accept that the setting is the personal setting of Cash, but I need to understand the choise... i'm new to the 3dPrinting so I need to understand every step to improve my prints. actually here we are on the Ormerod section of the forum, so I suppose that also Cash have an Ormerod so I need to understand the choise of setting the filament diameter to 2.85 (is that volontary to compensate sby Zonzo - Ormerod
Hi, i'm using: Cura 14.03 firmware 0.57t-dc42 (thanks again!!) (i'll update to the last soon) Cash plugin dated 23-03-2014 Cash Profile and preference dated 18-3-2014 my doubt is about the setting: after load the Cash profile and preference on the Cura folder (Win7 C:\Program Files (x86)\Cura_14.03\Cura), when i open Cura i found some settings wrong for the Ormerod (at least i think...): filaby Zonzo - Ormerod
ciao di nuovo, mi chiamo Giuliano, faccio l'impiegato (anche se al momento non faccio altro che impazzire chino sulla Ormerod) già che ci siamo, qualcuno se la sente di consigliarmi come modificare i file stl dei componenti della Reprap?? ho fatto un paio di migliorie tecniche ma me la cavo meglio con il tornio che non con i programmi di modellazione 3d e ora non ne vengo a capo nel modificareby Zonzo - Presentazioni, Off Topic e le migliori stampe
ok, infatti lo avevo davanti al naso... ora il valore è a 1, quanto consigli di provare? provo con 2 o uso i decimali?by Zonzo - Stampa 3D per principianti
Ciao Lion, grazie per la risposta, non sono molto pratico però... per randomizzare il punto di partenza nessun problema, ho trovato subito il flag su Slic3r (anche se mi domando se il rischio non sia quello di avere una superficie ancora più irregolare anzichè concentrare i difetti su una zona). non trovo invece dove settare il valore di retraction, che è quello che volevo provare a fare sin dby Zonzo - Stampa 3D per principianti
Ciao a tutti, ho da qualche giorno assemblato la mia Ormerod RepRapPro, ho fatto qualche stampa per tarare gli assi e sistemare il letto di stampa, non mi lamento del risultato, ma se stampo dei pezzi un po' più complessi, come gli ingranaggi dell'asse Z ho dei fastidiosi riporti su ogni punto di partenza del nuovo Layer... non sono sicuro sia solo quello, e in ogni caso non so dove andare a moby Zonzo - Stampa 3D per principianti
Ciao a tutti, mi sono appena iscritto in cerca di aiuto dopo aver dato una letta a questo o a quel topic in cerca di sistemare i parametri della mia Ormerod. spero di metterla a regime presto, quindi per il momento vi saluto e vado a scrivere un altro post chiedendo consigli. ciaoby Zonzo - Presentazioni, Off Topic e le migliori stampe