Thanks for the information. I got a tip from a friend who bought a reasonable priced switch mode supply that does 25A. Now there's still the probably wrong wiring.by m - RAMPS Electronics
@ Traumflug: If I add it to the wiki page, will you provide the information?by m - RAMPS Electronics
Well, the wiki also tells me that 16A are sufficient. I think this thread proved so far that blindly following the wiki does not seem to be a good idea. I'll add your information to the wiki. No problem.by m - RAMPS Electronics
So unless I want to brag about how accurately my psu can supply 12V, I'll be fine with an ATX. Getting my printer together becomes increasingly tedious with contrary answers in this forum. =( Any ideas on the motor cables?by m - RAMPS Electronics
What's the problem with ATX? Why would I want a psu that adheres to intel standard? To me, getting a server grade psu for a couple of stepper motors seems to be excessive and expensive. Please elaborate on that. --- I'm still stuck as I'm not sure if the wiring of my motor cables should be changed or not.by m - RAMPS Electronics
Ok, would you recommend one of those standardised switchmde psu or a ATX psu?by m - RAMPS Electronics
hi, I would like to know which power supply I can use for the ramps 1.4 electronics. I do plan to use a heated bed. According to the wiki, I will need 5 + 11 A. I found the SNT MW200-12 from MEANWELL for ~40€ It does 12 V and 16.7 A. Now I wonder if .7 A overhead is big enough if some peaks occur. How much more than the bare minimum of 16 A should the psu be capable of? What other psu wouldby m - RAMPS Electronics
hello, I'm currently trying to assemble a hotend. I tried to follow this list of instructions: The resistor does not fit into the head at all. It's way too small. The inner diameter of the head is about 6.1mm and the outer diameter of the resistor is only 5mm. How do I fix that? The how-to mentions wrapping with kitchen foil, but wrapping kitchen foil tight enough seems to be difficult if notby m - Reprappers
Über die kompletten kits bin ich natürlich auch schon gestolpert, kommt für mich allerdings nicht in Frage. Ich möchte wissen wie man so einen Drucker zusammenbaut und was wie wo zu beachten ist. Mit den Holzgeräten kann ich mich nicht anfreunden. Die Bauanleitung ist richtig spitze. Viel besser als die auf reprap.org. Mit Plexiglas, wie anschaulich. Gut, Arduino bekomme ich hinterher geschmiby m - Allgemeines
jsturm Wrote: ------------------------------------------------------- > "also woher soll ich es wissen? " > Du ließt die Postings nicht richtig durch. Ich > habe Dir erklärt, warum der ausgesuchte Wade > nicht zum ausgesuchten Buda passt -> > > 8#msg-229788 Ich lese die postings, keine Sorge. Die Frage war woher ich aus einem mit nicht mehr als "Greg Wade extruder" betiteltby m - Allgemeines
jsturm Wrote: ------------------------------------------------------- > Buda kann auch mit Wade - es muß aber ein > besonderer Wade sein - nicht das reprap-fab und > nicht das J-Head Modell (aus dem Plastiksatz). > Mach doch was du willst - aber fang später nicht > an zu jammern, wir hätten dich nicht gewarnt Dann nenn mir bitte eine Quelle, bei der ich den richtigen Wade bekommeby m - Allgemeines
In der Beschreibung steht, Buda könne ganz gut mit Wade und Greg e3D dauert auch 4 Wochen - fällt aus Ich werd es einfach mal probieren.by m - Allgemeines
jsturm Wrote: ------------------------------------------------------- > Deine Auswahl klingt wie: > Ich nehme eine Motor von Peugeot -> der ist > sparsam > einen Auspuff von Ferrari -> der klingt gut > die Karosse von Chevy -> ist so sexy > etc. > Würdest Du im realen Leben nie machen - warum bei > einem 3-D Drucker Also erst soll ich so einkaufen, als würde ichby m - Allgemeines
Ich bin weiter dran an der Sache. Bei vielen angebotenen Kits gab es keine Angabe, ob die Führungen gehärtet sind, ich nehme mal an, das sie es dann nicht sind. Hier mal der aktuelle Stand der Liste: Prusa i3 Aluminium frame 6 Führungsstangen, gehärtet 5 Schrittmotoren Prusa i3 gedruckte Teile Gt2 Riemen, Metallkleinteile, Lager, Extruderzubehör Gewindestangen Elektronik Heizbett 3 Endlagenschaby m - Allgemeines
jsturm Wrote: ------------------------------------------------------- > QuoteIch weiß das man für ca 400€ einen gut > funktionierenden Drucker bauen kann, > Wenn du das weist, warum fragst Du uns dann. Mach > einfach Werd ich ja, möcht ich ja, sitze auch schon wie auf Kohlen, nur ist die Frage wo es sich lohnt, etwas mehr Geld in die Hand zu nehmen. Jetzt muss ich zB ein besseres kiby m - Allgemeines
Hardwarekiller Wrote: ------------------------------------------------------- > Mal nen andere Frage, > wenn du in eine Gaststätte gehst bestellt du da > auch IMMER nach dem Preis ?, oder nachdem WAS du > Essen möchtest und was das Essen für eine > Qualität hat, oder ist das dir egal ? > Ich frag nur mal weil du da Äpfel mit Birnen > vergleichst > Die Frage ist WAS willstby m - Allgemeines
Hardwarekiller Wrote: ------------------------------------------------------- > Meine Empfehlung für die Elektronik ist > > R > amps LCD komplett > > R > amps Grafik komplett Beide enthalten ein Arduino mega, welches ich ja schon besitze. Außerdem frage ich mich, ob ich eine Anzeige wirklich benötige, da sich diese ja sicherlich auch über den zum drucken angeschlossenen PCby m - Allgemeines
Hallo reprapler, ich habe beschlossen einen 3D Drucker zu bauen. Ich denke die folgenden Fragen provozieren die, was ich eigentlich drucken möchte. Das kann ich euch aber auch nicht sagen und da der Drucker Teile für einen anderen erstellen kann würde ich einfach mal mit einem Drucker anfangen wollen, der preisgünstig und einfach zu bauen ist. Welches Modell würdet ihr empfehlen? Ich habe schoby m - Allgemeines