QuoteDust F is fan speed You need #define SET_PROGRESS_MANUALLY Thank you Next question. How can I get rid of the "E" in front? And how can I use hh:mm instead off mm:ss? Has this something to do with durartion_t.h? #define SHOW_ELAPSED_TIME // Display elapsed printing time (prefix 'E') And how can I disable the van value in % on the display? I dont need that. Thank you in advanceby Nitec0re - Firmware - Marlin
I lost my old and well working Marlin bugfix-2.0.xxxx.... ( i dont know). So I decided to use the newest. So far so good, but I have a strange problem and IDK where I can change that in the firmware. Before the print starts, the display shows the following info: Then, when he is printing: The first "100%" is clear, but what the heck is the second "100%" ? And the second thing is... why theby Nitec0re - Firmware - Marlin
Ich habe mir ein SKR v1.3 board und TMC2208 Treiber zugelegt. Die Brücke für UART ist gelötet und es funktioniert auch soweit (Einstellungen via Display). Jedoch habe ich ein Problem damit. Wenn ich die Treiber im UART betreibe, dann hört sich das Ganze (X. Y und Z) so an, wie wenn Sand zwischen Riemen und Zahnrad wäre. Stelle ich in der FW (Marlin) die Treiber auf Standalone um, dann sind die sby Nitec0re - Elektrik & Elektronik
Thank you Thats sad about creality. They dont released any schematic of the 10S-Pro mainboard yet. Its only available from the normal 10S. Maybe this mainboard stays closed source...by Nitec0re - Firmware - Marlin
R64 and R66 are already connected - otherwise, the reprap display would not work. So they are bridged.by Nitec0re - Firmware - Marlin
I dont need the SD card. The board itself has one, and i use octoprint - so thats no a problem. The solder points between LCDE and LCDRS are ATM connected for the reprap display - otherwise it wont work. Did I understand it correct, that i have to disconnect LCDE and LCDRS to make it work? And do i change the firmware to make it work? I have no idea about pin definitionby Nitec0re - Firmware - Marlin
in configuration.h you will find // Homing speeds (mm/m) #define HOMING_FEEDRATE_XY (50*60) #define HOMING_FEEDRATE_Z (6*60) lower these values and the probing should be slower. and // Feedrate (mm/m) for the "accurate" probe of each point #define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) <-- The "2" means, that the second probe is half of the first speed. Do you need it even slower, rby Nitec0re - Firmware - Marlin
Hello I have a Creality CR10S-Pro. The satndard display is a touch screen, but i didn't like, so i replaced it with a 12864 reprap full graphic controller. I made all changes to the firmwate (1.1.9) and it works great. While browsing on aliexpress i saw the Fysetc Mini 12864 display. I ordered one, because i thought, that this display will work with the 10S-Pro mainborad - like the reprap does.by Nitec0re - Firmware - Marlin
Hello I have a Anet A8 and I'm convert it to a AM8. So I tough, I change the Display too. I bought this It is a 20x4 OLED Display with a HDD44780 compatible controller. So far so good - I think But I have some weird problem/behavior -> And this is not the only one. The horizontal Lines are at the wrong position. Is: X 0 Y 0 Z 0 Temp.Nozzle 0/0 Heatbed 0/0 AM8 Printer ready 100% Time: 0by Nitec0re - Firmware - Marlin
Hallo zusammen Ich bin dabei mein Anet A8 zum AM8 umzubauen. Und weil mir das balue Display nicht gefiel, schaute ich mich nach einem anderen um. Habe dann ein OLED bei Farnell gefunden Dieses Display hat einen HDD44780 kompatiblen Controller. Also dachte ich mir, sollte ja funktionieren weil ich auf meinem A8 Marlin 1.1.8 betreibe und das Standard Display auch ein LCD 2004 mit einem HDD4478by Nitec0re - Elektrik & Elektronik