Search results

Jump to: navigation, search

Create the page "RepRap/" on this wiki! See also the search results found.

  • Generation 2 Electronics
    Once you start putting electricity into your RepRap - even at just 12 volts - you have to take basic, common sense precautions ...to do this is to [[PCPowerSupply|convert a normal PC power supply]] into a RepRap power supply. Its simple, cheap, and all the boards are designed to accept
    14 KB (2,223 words) - 09:27, 26 November 2011
  • Generation 2 firmware
    = RepRap 2nd Generation Firmware = ...uino - with the SNAP protocol that we used for the original PIC-controlled RepRap. New users should go for G Codes.
    16 KB (2,592 words) - 06:53, 18 July 2015
  • Generation 3 Electronics
    Once you start putting electricity into your RepRap - even at just 12 volts - you have to take basic, common sense precautions * 1 [[Motherboard_1_2|RepRap Motherboard]] (''mendel/electronics/motherboard''),
    10 KB (1,606 words) - 20:53, 19 February 2012
  • Generation 3 firmware
    = RepRap Generation 3 Firmware = '''Host Device''' - This is your computer that controls the RepRap and issues commands and queries. As of this writing, the only software tha
    5 KB (745 words) - 06:53, 18 July 2015
  • Glossary
    This is a list of common terms and abbreviations used in the RepRap community. The moving middle assembly on the x-axis of a RepRap which holds the extruder. Often referred to as: ''x-carriage''.
    17 KB (2,735 words) - 22:34, 1 May 2024
  • PSMD Triple Axis Stepper Driver
    |reprap = Pololu Electronics
    4 KB (586 words) - 05:56, 29 November 2014
  • GranuleExtruder
    The [[RepRapOneDarwinThermoplastExtruder|standard RepRap polymer extruder]] works very reliably, is simple, and can be made almost a ...e the [http://blog.reprap.org/2006/02/initial-experiments-on-filament.html RepRap blog for Friday, February 17, 2006] and the subsequent fortnight).
    6 KB (986 words) - 09:46, 19 September 2013
  • HackingGM3Gearmotor
    The GM3 gearmotor is the standard motor for the RepRap extruder. There are a couple things you can do to make it function better.
    7 KB (1,097 words) - 18:36, 8 May 2014
  • HardwiredSerialPorts
    The RepRap itself can run off any RS232 serial port, but the [[StripboardJDM|JDM PIC P ...ith a donation, so we can do more of the research necessary to develop the RepRap:
    6 KB (1,035 words) - 12:59, 7 July 2014
  • HotWaxSyringe
    ...se. At this point in time a you can make some really useful things with a reprap machine.
    857 bytes (142 words) - 18:38, 25 October 2010
  • HotplateReflowTechnique
    ...of SMD parts have fairly big pads, especially the SMD part that we use for RepRap. Resistors, capacitors, LEDs, 7805s, etc. have large pads. Simply apply s # Use your other hand to steady it. It really works well. To use some RepRap terminology: Use your main hand as the XY positioning, and use your second
    14 KB (2,503 words) - 06:59, 3 September 2019
  • HyperbolicSpeed
    The PIC microcontrollers used in the RepRap project express timer and speed values as a number from 0 to 255.
    3 KB (525 words) - 06:36, 11 January 2015
  • ICProgHints
    ...program used to program serial-programmable ICs, including the PIC used in RepRap. See http://www.ic-prog.com Also (thanks to bartlee45 on the RepRap forums) you need to go to Settings->Options then select Misc tab and check
    1 KB (180 words) - 17:14, 28 November 2011
  • IOBox
    ...ists keen to exploit the simple and inexpensive technologies developed for RepRap in other projects - please do! Currently there is no specific board, but is ...sion|Subversion]] at [http://reprap.org/svn/reprap/firmware/devices/iobox/ reprap/firmware/iobox]
    1 KB (187 words) - 17:17, 28 November 2011
  • PIC in-circuit programming
    ...uit_serial_programming In-circuit serial programming]'''; '''ICSP'''): The RepRap controller boards have been designed to allow you to program the PIC chips ...a three-pin and a two-pin socket. The three-pin socket will plug into the RepRap Universal Controller board where the Max/Empty opto-switch normally goes.
    3 KB (495 words) - 15:28, 23 July 2015
  • Introduction
    '''RepRap is short for Replicating Rapid-Prototyper.'''
    1 KB (171 words) - 13:48, 12 May 2015
  • ItemsMade
    This page shows some samples made by prototype and production RepRap machines. ...at were sold to someone else. Cost: One case of beer... The person who's RepRap made them is Wade Bortz.
    7 KB (1,195 words) - 08:01, 2 January 2015
  • JavaComm
    ...nd currently needs this library installed in order to communicate with the RepRap modules. ...on Windows is very straightforward. Just copy the JavaComm files to your reprap/host/lib directory:
    4 KB (743 words) - 19:56, 26 November 2011
  • JavaCommsLibrary
    [[Subversion|Subversion]] Location: /reprap/host
    471 bytes (70 words) - 19:56, 26 November 2011
  • KiCad
    RepRap is using KiCad for electronic design. The KiCad homepage is http://www.kic ...Those should be on a metric grid to interface more easily with the rest of RepRap. Kicad flips between imperial and metric with a single button click; you m
    6 KB (1,078 words) - 12:08, 26 October 2021

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)

Retrieved from "https://reprap.org/wiki/Special:Search"