Search results

Create the page "Useful Software Package" on this wiki! See also the search results found.

• RUG/Pennsylvania/State College/RepRap Media Timeline
  Summary: A 3D printing enthusiast set out to prove that useful items can be created by RepRaps by designing and printing all necessary par ...ty of Nevada, Reno has added two 3D printers, a 3D scanner, and supporting software available for general use to the school community. Thanks to professor Tod
  152 KB (22,645 words) - 01:20, 30 August 2019
• LongboatPrusa
  * A Dremel is useful for trimming the M8 mudguard washers ...tensioned so that there is little or no slack. (a second pair of hands is useful for this)
  49 KB (8,221 words) - 09:42, 26 March 2014
• PrusaBuildNotesBraino
  I'm not do good with electronics (I'm more of a software guy), and saved my self at least a couple weeks with the solidoodle part. == Software ==
  59 KB (9,978 words) - 17:05, 12 April 2015
• LulzBot/AssembledPrusaMendel/gettingstarted
  ...setting up your printer make sure all of the items on the list are in your package. =Getting software=
  14 KB (2,517 words) - 12:37, 14 March 2012
• Stepper motor driver
  ! Package ...s 1/16 microstepping, and some people prefer this TSSOP package over a QFN package.
  23 KB (3,496 words) - 07:24, 1 May 2018
• USBasp
  ...ore'' the 10pin header, made sure there were no solder-bridges and ran the software.<br> =Software=
  4 KB (664 words) - 01:01, 23 August 2015
• FilamentEsunplaReviews
  From the time I sent the money via paypal, it took 13 days to receive the package in Pennsylvania, USA. ...ite a bit when idle in the extruder. After that, and adjusting my extruder/software for the 1.7mm filament, I started Printing.
  5 KB (883 words) - 11:51, 19 March 2014
• Printrboard
  ==Software== ...ac/Linux: packaged with [http://www.atmel.com/tools/FLIP.aspx Atmel's FLIP software].
  23 KB (3,566 words) - 13:32, 11 March 2020
• Gen7 Board 1.4.1
  * Download and unpack or install the [http://arduino.cc/en/Main/Software Arduino IDE]. You need v1.0.3 or later. If you insist on v0023 or earlier f ...bootloader. Bootloader binaries come with the [[Gen7 Arduino IDE Support]] package, so upload instructions can also be found [[Gen7 Arduino IDE Support#Bootlo
  52 KB (8,394 words) - 15:13, 14 November 2015
• Azteeg X1
  ...t 12v power supply of yours). You need to use a higher rated TVS diode(SMB package) if using a higher voltage power supply.}} === Software ===
  13 KB (2,228 words) - 18:42, 18 November 2014
• XtruBot
  ...xpress/ PTC Creo Elements/Direct Modeling Express 4.0] as the CAD software package to develop custom 3D RepRap parts and assemblies for XtruBot<br> * Conducted a cursory review of available G-Code software and tentatively selected [http://replicat.org/ ReplicatorG] for use with Xt
  7 KB (1,109 words) - 15:08, 22 March 2012
• Gen7 Board 1.4.1/fr
  * Téléchargez, décompressez et installez [http://arduino.cc/en/Main/Software|Arduino IDE].Vous devez utiliser la version 2.0 ou celle suivante. Si vous ...%20Arduino%20IDE%20Support%202.0.zip?raw=true Gen7 Arduino IDE Support 2.0 package].
  72 KB (11,247 words) - 21:00, 31 January 2013
• WPI Rostock Distro
  ...WPI [[Rostock]] distribution is a complete software and hardware sourcing package. In order ease the construction and support of the Rostock at WPI.
  537 bytes (71 words) - 09:01, 23 January 2016
• Clone Wars Distro/es
  Creación de una distribución de Linux que reuna el software necesario para imprimir prusamente. ** [http://www.kicad-pcb.org/display/KICAD/KiCad+EDA+Software+Suite Kicad]
  4 KB (543 words) - 20:52, 17 March 2014
• Rostock MAX
  == Software and Setup == Repetier-Host is a great software package that bundles the toolpathing program Slic3r with a great machine control as
  34 KB (6,005 words) - 13:50, 14 December 2014
• Clone Wars Distro/en
  Creating a Linux distribution that meets the necessary software to print prusamente. ** [Http://www.kicad-pcb.org/display/KICAD/KiCad+EDA+Software+Suite Kicad]
  3 KB (396 words) - 20:52, 17 March 2014
• Sango bc
  * software selectable stepper modes * software selectable current control
  2 KB (281 words) - 21:04, 11 December 2012
• Sanguinololu/es
  la Versión 1.3a no tuvo cambios en el software - La asignación de pines se mantiene igual y su firmware compatible 1.2+ t Una corrección de software es utilizar la rutina de carga del GEN7 que no enciende un LED no existente
  46 KB (7,281 words) - 00:24, 15 September 2015
• LongboatPrusa/ptBR
  * A Dremel is useful for trimming the M8 mudguard washers ...tensioned so that there is little or no slack. (a second pair of hands is useful for this)
  51 KB (8,583 words) - 12:40, 11 October 2012
• SharebotLC/en
  == Software == Management software for DIY 3D printers there are several, for practicality and reliability we
  42 KB (7,356 words) - 10:30, 15 October 2012

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)