Welcome! Log In Create A New Profile

RepRap en Español

Page 21 of 29 Pages:

19 202122 23

Forum List New Topic RSS

	Views	Posts	Last Post
continuar impresion tras error by vhailor	3,527	9	04/17/2013 05:15AM Last Post by JuanJose77
Parámetro de Slic3r - Vibration Limit by JuanJose77	941	1	04/16/2013 02:23PM Last Post by JuanJose77
[COMPRO] Piezas Impresas RepRap Air 2 by anrusal	813	1	04/15/2013 03:16PM Last Post by anrusal
Antes de emprimir (Pages: 1 2) by Juan	2,342	35	04/12/2013 07:11AM Last Post by thingmaker
Problema movimiento Ejes en primera arrancada. by Josep BP+	915	5	04/06/2013 04:44PM Last Post by Josep BP+
Problemas con los rellenos by cerojugadores	782	2	04/05/2013 04:59AM Last Post by misan
Altura del eje Z comienza bien y acava mal by Juan	837	3	04/02/2013 11:02PM Last Post by Juan
3D Printers-shop NUEVA TIENDA ONLINE ESPAÑA by 3dprinters-shop	1,021	1	04/01/2013 01:26PM Last Post by 3dprinters-shop
Problema eje x by proalius	629	2	03/31/2013 02:30PM Last Post by proalius
Problemas con la temperatura del extrusor by juanmavargas00	1,133	5	03/27/2013 07:16PM Last Post by juanmavargas00
temperatura hotend correcta by vhailor	1,361	11	03/27/2013 10:49AM Last Post by eneko
Prueba nuevo extrusor by proalius	852	1	03/27/2013 06:10AM Last Post by proalius
Hotend by SLG	841	4	03/27/2013 05:47AM Last Post by thingmaker
Problemillas con mi primeras pruebas by JuanJose77	1,497	8	03/22/2013 05:35PM Last Post by JuanJose77
Repuesto by InriXs	730	1	03/22/2013 11:19AM Last Post by InriXs
Compro nozzle en Madrid by proalius	799	1	03/14/2013 08:50AM Last Post by proalius
Problemas Ramps 1.4 y Sprinter by proalius	1,328	7	03/13/2013 01:05PM Last Post by Juan
Ayuda para usar unos motores unipolares by Yamagata	2,478	3	03/13/2013 08:59AM Last Post by Yamagata
Nuevo extrusor - Fary Nozzle- by c.monreal	1,732	4	03/12/2013 03:39AM Last Post by algspd
Ayuda me acabo de cargar un pololu by juanmagaor	824	3	03/09/2013 03:52AM Last Post by juanmagaor
inquietud reprap by jlviloria	751	4	03/08/2013 07:53AM Last Post by jlviloria
Pierdo el control de los motores al imprimir. by txibi	1,790	9	03/08/2013 03:09AM Last Post by benzuria
Motores solo funcionan en una direccion by serecac	1,416	29	03/06/2013 05:15PM Last Post by electropluma
AYUDA CON SANGUINOLOLU by jota17	1,719	21	03/03/2013 08:27AM Last Post by misan
prueba de ramps 1.4 y 1 motor by vhailor	3,137	5	03/02/2013 04:02PM Last Post by mpakiam
REGEMAT 3D: Suministro de componentes e impresoras RepRap y otros servicios de ingeniería. by Regemat3D	802	1	03/01/2013 05:55AM Last Post by Regemat3D
Ajustando la cantidad de extrusión midiendo el ancho resultado by electropluma	833	4	02/27/2013 04:31PM Last Post by Yamagata
Recmendais comprar en bricogeek? by Alfon	2,375	11	02/27/2013 05:27AM Last Post by vhailor
tension de correas by vhailor	1,016	11	02/25/2013 05:17AM Last Post by electropluma
Desunión entre perímetros y relleno by InriXs	1,011	9	02/25/2013 05:13AM Last Post by electropluma

Page 21 of 29 Pages:

19 202122 23

RepRap en Español

Antes de emprimir (Pages: 1 2)