Welcome! Log In Create A New Profile

Advanced

RepRap en Español

Page 22 of 29    Pages: FirstPrevious2021222324NextLast
Forum List New Topic RSS
Subject Views Posts Last Post

Desplazamiento eje Y o backslash al imprimir 2 piezas al mismo tiempo

by thingmaker 		1,003 4 02/22/2013 11:58AM
Last Post by Gaodesign

Dudas configurando el Marlin

by JuanJose77 		1,790 4 02/22/2013 04:29AM
Last Post by thingmaker

Liberado el diseño de la RepRap BCN3D

by RepRapBCN 		1,565 5 02/21/2013 04:52PM
Last Post by eneko

Conexión/Desconexión de la fuente de alimentación mediante RAMPS 1.4

by thingmaker 		3,027 9 02/21/2013 10:11AM
Last Post by misan

Instalar SD en Ramp's 1.4

by pikelo 		3,922 17 02/21/2013 06:32AM
Last Post by misan

Arduino - no abre spriter

by Juan 		1,255 2 02/17/2013 01:05PM
Last Post by Juan

Puesta en marcha ... problemas con ejes Z y Y

by thingmaker 		2,214 26 02/11/2013 06:23AM
Last Post by misan

Ventilador para los controladores en RAMPS 1.4

by thingmaker 		2,919 7 02/11/2013 05:43AM
Last Post by thingmaker

hotend J-Head IV

by bcndynamics 		1,297 2 02/05/2013 07:17AM
Last Post by benzuria

Rams 1.3 es posible conectarlo un lcd para controlar la empresora 3d

by Juan 		772 3 02/04/2013 08:23PM
Last Post by Juan

Duda en la seleccion de los motores

by edy5150 		1,544 12 02/04/2013 05:46AM
Last Post by thingmaker

Varios problemas

by oriol414 		944 4 02/03/2013 06:12PM
Last Post by Yamagata

Spray, laca de pelo para sustituir la Kapton   (Pages: 1 2)

by benzuria 		11,003 43 01/31/2013 08:19AM
Last Post by thingmaker

RepRap en Venezuela

by rikyorangekox 		987 2 01/30/2013 01:41PM
Last Post by Freddystrubinger

Poblema calibrado con cubo 20X20

by cacer 		1,052 4 01/27/2013 04:59AM
Last Post by cacer

Mejoras, mejoras y más mejoras.....

by electropluma 		791 3 01/26/2013 08:11PM
Last Post by Yamagata

Plataforma nivelable con dos tornillos

by Mecano 		1,557 7 01/26/2013 01:40PM
Last Post by Mecano

Instalando Pronterface en Raspberry pi

by PtxLupen 		3,706 4 01/26/2013 04:27AM
Last Post by misan

Dudas sobre los parámetros de configuración Sprinter

by Suca 		1,619 12 01/25/2013 06:03AM
Last Post by Suca

Puentes con PLA

by PtxLupen 		1,037 4 01/24/2013 03:07AM
Last Post by PtxLupen

Proveedores en Argentina   (Pages: 1 2 3 4)

by Pablo2m 		12,466 98 01/22/2013 06:16PM
Last Post by ezequiel

Dudas sobre slicing

by guille 		1,140 3 01/21/2013 05:55PM
Last Post by guille

Accidente en pasta térmica en los disipadores

by thingmaker 		5,094 12 01/21/2013 03:16PM
Last Post by electropluma

Ramps 1.4 no funcionan

by Patxuloyo 		1,825 3 01/20/2013 03:45AM
Last Post by Patxuloyo

Flow control

by PtxLupen 		1,040 4 01/19/2013 06:34PM
Last Post by electropluma

Hola, ¿podrian darme guia en la creacion de mi primera impresora 3d?

by templariomaster 		2,519 29 01/19/2013 01:21PM
Last Post by electropluma

Indignación! - Medios manipuladores

by Yamagata 		1,008 7 01/19/2013 05:02AM
Last Post by JuanJose77

Rep Rap Barcelona

by SebasRepRapBCN 		1,400 8 01/18/2013 02:46AM
Last Post by RepRapBCN

Repetier IDE+Marlin+RAMPS 1.4

by PtxLupen 		920 5 01/11/2013 08:22PM
Last Post by PtxLupen

velocidad infill en zonas estrechas

by bcndynamics 		954 4 01/11/2013 06:32AM
Last Post by PtxLupen
Page 22 of 29    Pages: FirstPrevious2021222324NextLast