Welcome! Log In Create A New Profile

Advanced

Delta Machines

Rostock, Kossel, Simpson, 3DR, and more. See: http://reprap.org/wiki/Category:Delta. Previously named "Delta Robots and Stewart Platform" 
Subject Views Posts Last Post

Bowden strength question

by bifbuzz
684 5 02/01/2014 03:50PM
Last Post by brnrd

Has anybody tried 3mm filament in airtrippers filament drive for rostock?

by TheTechnicalNoob
1,260 11 01/31/2014 03:00PM
Last Post by TheTechnicalNoob

IPAnema - Parallel Cable Robot

by ShadowRam
673 1 01/31/2014 07:52AM
Last Post by ShadowRam

Printable area of Deltas (Rostock, 3DR,...)

by dolphinboy
997 4 01/28/2014 05:31PM
Last Post by dolphinboy

Automatic bed level issues Attachments

by Vinculum
1,759 5 01/28/2014 12:42PM
Last Post by DanielStein

Stepper motors clicking while printing

by thefuzzbl
637 5 01/25/2014 11:27PM
Last Post by thefuzzbl

Delta-Pi "Flexing" hub

by beamsaber
1,060 10 01/21/2014 08:49PM
Last Post by mikep-nz

3DR - my printer and mods

by dolphinboy
1,098 1 01/21/2014 05:49PM
Last Post by dolphinboy

LISA Simpson Take 2 Attachments

by nicholas.seward
1,835 16 01/21/2014 12:35PM
Last Post by uncle_bob

Jazzabell - 3DR printer

by Bajn
3,083 9 01/16/2014 04:11AM
Last Post by Bajn

Current best version of Marlin for a 3DR or 3DR Simple?

by brendanjerwin
1,053 2 01/14/2014 05:19AM
Last Post by TheTechnicalNoob

Mini Kossle Current Firmware Location?

by Enlightx
786 3 01/13/2014 11:21PM
Last Post by jaydmdigital

Kossel with heated bed - how is it possible?

by stahlsau
5,573 14 01/13/2014 06:11AM
Last Post by stahlsau

Best Direct Drive or Geared Extruder Mounted to Effector for Delta Printer?

by runninfarmer
4,371 6 01/09/2014 08:51PM
Last Post by TheTechnicalNoob

Offsets in configuration (again) eye rolling smiley Attachments

by wretan
2,193 5 01/09/2014 07:55PM
Last Post by hercek

BOB Simpson development

by TheTechnicalNoob
1,214 4 01/09/2014 04:44PM
Last Post by TheTechnicalNoob

I'm Stuck. Need help calibrating endstops and Delta Radius... Please

by disneytoy
1,221 2 01/05/2014 06:30PM
Last Post by AndyCart

delta printer - calibration problem

by Bajn
2,348 6 01/05/2014 01:59PM
Last Post by Bajn

Kossel Mini auto level deploy and retract position

by cephas77
3,890 9 01/04/2014 04:21PM
Last Post by TheTechnicalNoob

Building a Kossel Mini - BOM + Supplierlist

by Xhnnas
1,692 2 01/03/2014 03:16PM
Last Post by mnutsch

Looking to build a delta - could use a bit of input

by RickM
1,674 18 01/01/2014 12:07AM
Last Post by TheTechnicalNoob

Power Supply

by Bixx
920 6 12/31/2013 02:20PM
Last Post by Bixx

Have you seen the Delta-Pi? Attachments

by TheTechnicalNoob
2,336 24 12/29/2013 07:08PM
Last Post by beamsaber

Help with filament drive reels

by shaggysgti
977 9 12/29/2013 05:17PM
Last Post by shaggysgti

Kossel rails vs wheels

by Brekel
2,243 5 12/24/2013 08:06PM
Last Post by AndyCart

Delta4 Production Printer

by MattMoses
1,324 7 12/23/2013 12:15PM
Last Post by ddseeker

Scaling Kossel

by Justintime
2,817 5 12/17/2013 11:59PM
Last Post by TheTechnicalNoob

Delta-Pi Endstop Problem in Repeteir Attachments

by runninfarmer
2,000 23 12/17/2013 02:10PM
Last Post by mikep-nz

DELTA_EFFECTOR_OFFSET Question

by disneytoy
33,843 8 12/16/2013 03:50PM
Last Post by disneytoy

Question about z-probe

by disneytoy
606 1 12/16/2013 11:31AM
Last Post by disneytoy