Subject		Views	Posts	Last Post
	Prusa i3 runs for a while then reverses the extrusion motor by Krippers	371	4	01/18/2017 04:51PM Last Post by Krippers
	Small Print Not Sticking To Bed by Bottersnike	739	5	01/18/2017 01:39PM Last Post by Inhumierer
	How are you getting on with e3d silicone covers? by DjDemonD	377	2	01/18/2017 01:38PM Last Post by PDBeal
	Cold Bed & PLA: Kapton or Blue Tape by shaiss	2,074	10	01/17/2017 09:44PM Last Post by Hedgehog
	Borosilicate glass by Hedgehog	786	11	01/17/2017 09:40PM Last Post by Hedgehog
	Prints warping and coming off bed by Hedgehog	599	18	01/17/2017 09:39PM Last Post by Hedgehog
	Remove Buildtak glue from aluminium heating bed by Shinobi	967	6	01/17/2017 12:02PM Last Post by PDBeal
	Perimeter bonding problem on concave perimeters by Inhumierer	485	9	01/17/2017 03:03AM Last Post by Inhumierer
	Vertical lines by anil.bhatia	396	2	01/16/2017 08:35AM Last Post by o_lampe
	Printer under and over extruding?? by friarfish	649	11	01/16/2017 07:56AM Last Post by friarfish
	Heating failed on Prusa i3   (Pages: 1 2) by Aschie4589	8,412	32	01/16/2017 07:31AM Last Post by MCcarman
	Very very persistently bad printer... Running out of ideas by DannerD3H	1,377	8	01/16/2017 05:53AM Last Post by DannerD3H
	Bed heating issues by HighLikeAladdin	333	3	01/16/2017 01:51AM Last Post by HighLikeAladdin
	Extruder/nozzle issue and auto leveling question by barbrum	309	1	01/15/2017 01:03PM Last Post by barbrum
	Marlin v1.0.2 Y-axis offset issue by snoekel	834	5	01/15/2017 04:49AM Last Post by Ciccillo
	Strange infill gaps by anvoice	1,549	9	01/14/2017 09:14PM Last Post by anvoice
	Looking for define board list for Mega 2560 number by hugetoughguy	427	2	01/14/2017 07:32PM Last Post by obewan
	Can't connect to printer by bmcnicho	646	2	01/14/2017 06:35PM Last Post by Inhumierer
	Motors dont stop when pressing the home button in the repetier host. by ziayakens	395	4	01/14/2017 06:31PM Last Post by Inhumierer
	Having problems getting anything to heat properly by hugetoughguy	348	2	01/14/2017 06:07PM Last Post by Inhumierer
	Extruder is too far off bed/keeps hitting side of it by ajcifuentes27	397	3	01/14/2017 07:27AM Last Post by the_digital_dentist
	Bonding of flex PLA with non-flex PLA by Replace	616	7	01/12/2017 05:56PM Last Post by Replace
	Erratic Temperatures by RickRap	382	5	01/11/2017 09:03PM Last Post by the_digital_dentist
	After Print Best Practices Help by spin99	419	8	01/11/2017 02:25PM Last Post by JamesK
	Very minor step skipping by Lazerlord	403	3	01/10/2017 07:57PM Last Post by Lazerlord
	Z probe - trying to calibrate and failing by ss002d6252	452	5	01/09/2017 12:28PM Last Post by ss002d6252
	Stepper motor issue on X,Y,Z - can't find problem by elkell	625	6	01/07/2017 03:30PM Last Post by elkell
	Printing with Palette 3D by drmaestro	349	1	01/06/2017 03:31AM Last Post by drmaestro
	A problem with cube corners... but not the usual one by animoose	688	4	01/05/2017 04:01PM Last Post by animoose
	Extruder motor stops mid print. by Hatmpatn	1,320	6	01/05/2017 10:42AM Last Post by Hatmpatn