Welcome! Log In Create A New Profile

Advanced

RepRap Usergroup - Argentina

http://reprap.org/wiki/RUG/Argentina - Lista de proveedores, Reuniones, y ayuda al futuro RepRapper  
Subject Views Posts Last Post

Diseño Impresora Low Cost (Buscando una placa electrónica)

by Yko999
1,976 7 02/05/2019 06:27PM
Last Post by tolemaxdream

CYCLONE PCB

by manuel-241
1,505 1 01/20/2019 07:44PM
Last Post by manuel-241

Fan de capa

by Rolo
1,444 1 01/05/2019 06:42AM
Last Post by Rolo

Impresión espejada de la pieza Attachments

by Rolo
1,320 4 12/21/2018 09:48AM
Last Post by Rolo

Problema motor paso a paso

by Nicotina2018
1,863 3 11/03/2018 11:54AM
Last Post by LZZ77

PROBLEMA EXTRUSOR Attachments

by manuleaniz
1,464 3 11/03/2018 11:53AM
Last Post by LZZ77

Ventilador del hotend Attachments

by pjfry
2,208 5 11/03/2018 11:52AM
Last Post by LZZ77

consulta voltaje motores paso a paso epson

by [email protected]
14,430 6 11/03/2018 11:48AM
Last Post by LZZ77

Conversión Hotend de 3mm a 1.75mm

by pola
1,447 3 11/03/2018 11:38AM
Last Post by LZZ77

Marco y piezas plasticas

by Mattni
1,060 2 11/03/2018 11:37AM
Last Post by LZZ77

pi3_co*1.gco

by ngvending
1,162 3 11/03/2018 11:36AM
Last Post by LZZ77

Baja de temperatura al activar fan de capas

by mbr386
998 2 11/03/2018 11:35AM
Last Post by LZZ77

Impresora 3d para niños

by SaraMartinez
1,016 2 11/03/2018 11:34AM
Last Post by LZZ77

Se me derrite la bornera

by rigatuzo
2,482 19 08/16/2018 07:57AM
Last Post by gorgojo

QUEME EL REGULADOR DE VOLTAGE DEL MEGA 2560sad smiley NONONO¡¡¡

by aleiovanevcp
4,744 11 08/16/2018 07:49AM
Last Post by gorgojo

convertir unipolares a bipolares   (Pages: 1 2 3)

by chico3D
28,877 89 07/04/2018 09:52AM
Last Post by Oslay

Impresora 3D DIY : Eje Z desciende en ves de mantenerse en el punto Máximo al Imprimir.-

by axmacron
807 3 05/22/2018 01:45PM
Last Post by igbs

Marlin - Problema con el Home (endstop)

by marcelogustavo
1,757 2 05/22/2018 11:04AM
Last Post by igbs

No aparece activa la sd en LCD RepRapDiscount Smart Controller confused smiley

by cloxx78
838 2 05/22/2018 09:30AM
Last Post by igbs

Impresora Delta casera de 25X30 y Calibración

by diegognavarro
3,241 15 04/27/2018 12:42PM
Last Post by sarindangui

Solo gira en un solo sentido el eje Z ????

by cloxx78
732 1 04/18/2018 10:54PM
Last Post by cloxx78

Infill Vs. Resistencia

by diter23
788 7 03/19/2018 08:48AM
Last Post by ldcampana

PRESENTACION

by artesano
636 1 03/13/2018 08:32AM
Last Post by artesano

EXTRUSOR MK8

by lea.alm.nat
716 1 03/06/2018 02:48PM
Last Post by lea.alm.nat

Problemas con Extrusor Externo

by SG-1
571 2 02/26/2018 12:29PM
Last Post by SG-1

Movimiento de impresora fuera de escala

by Taglio
631 2 02/06/2018 02:54PM
Last Post by diegognavarro

Armado de impresora S-BOX CORE XY Attachments   (Pages: 1 2 3 4)

by maic
10,507 110 01/29/2018 09:18PM
Last Post by diegognavarro

Corte de aluminio para marco de Prusa I3 custom

by ldcampana
681 3 01/19/2018 07:27AM
Last Post by ldcampana

Mi home no va bien en mi impresora

by edgar360
524 2 12/26/2017 04:07PM
Last Post by diegognavarro

Ayuda - Molde Vasos Sustentables! Attachments

by enepece
579 2 11/11/2017 10:26AM
Last Post by tatubias