Welcome! Log In Create A New Profile

Advanced

RepRap Usergroup - Argentina

http://reprap.org/wiki/RUG/Argentina - Lista de proveedores, Reuniones, y ayuda al futuro RepRapper  
Page 1 of 36    Pages: 12345NextLast
Forum List New Topic RSS
Subject Views Posts Last Post
Sticky

thumbs up Venta General (Kits, Plásticos, Frames, Hot-Ends y demás)   (Pages: 1 2)

by epoxi 		21,760 39 04/03/2018 04:55PM
Last Post by matiasdj87
Sticky

smileys with beer Trueques (KITs, partes, servicios, etc)   (Pages: 1 2)

by epoxi 		14,540 31 06/18/2016 09:15AM
Last Post by ngvending
Sticky

smiling smiley Ofrecidos

by epoxi 		6,410 7 06/07/2016 02:27PM
Last Post by briancatala
Sticky

Leer antes de postear – Reglas y lineamientos

by epoxi 		5,697 1 08/06/2014 06:14PM
Last Post by epoxi

Impresión espejada de la pieza Attachments

by Rolo 		23 2 12/16/2018 11:41PM
Last Post by diegognavarro

Problema con arduino mega 2560

by oiram27 		282 2 11/06/2018 08:16PM
Last Post by tatubias

Problema motor paso a paso

by Nicotina2018 		601 3 11/03/2018 11:54AM
Last Post by LZZ77

PROBLEMA EXTRUSOR Attachments

by manuleaniz 		291 3 11/03/2018 11:53AM
Last Post by LZZ77

Ventilador del hotend Attachments

by pjfry 		430 5 11/03/2018 11:52AM
Last Post by LZZ77

consulta voltaje motores paso a paso epson

by [email protected] 		9,292 6 11/03/2018 11:48AM
Last Post by LZZ77

Conversión Hotend de 3mm a 1.75mm

by pola 		105 3 11/03/2018 11:38AM
Last Post by LZZ77

Marco y piezas plasticas

by Mattni 		95 2 11/03/2018 11:37AM
Last Post by LZZ77

pi3_co*1.gco

by ngvending 		225 3 11/03/2018 11:36AM
Last Post by LZZ77

Baja de temperatura al activar fan de capas

by mbr386 		61 2 11/03/2018 11:35AM
Last Post by LZZ77

Impresora 3d para niños

by SaraMartinez 		103 2 11/03/2018 11:34AM
Last Post by LZZ77

Se me derrite la bornera

by rigatuzo 		918 19 08/16/2018 07:57AM
Last Post by gorgojo

QUEME EL REGULADOR DE VOLTAGE DEL MEGA 2560sad smiley NONONO¡¡¡

by aleiovanevcp 		2,596 11 08/16/2018 07:49AM
Last Post by gorgojo

Consulta

by mat_z3d 		142 1 07/06/2018 09:56PM
Last Post by mat_z3d

convertir unipolares a bipolares   (Pages: 1 2 3)

by chico3D 		21,335 89 07/04/2018 09:52AM
Last Post by Oslay

Impresora 3D DIY : Eje Z desciende en ves de mantenerse en el punto Máximo al Imprimir.-

by axmacron 		265 3 05/22/2018 01:45PM
Last Post by igbs

Marlin - Problema con el Home (endstop)

by marcelogustavo 		352 2 05/22/2018 11:04AM
Last Post by igbs

No aparece activa la sd en LCD RepRapDiscount Smart Controller confused smiley

by cloxx78 		290 2 05/22/2018 09:30AM
Last Post by igbs

Oferta empleo en impresión 3D, Buenos Aires

by paucus 		343 1 05/04/2018 11:21AM
Last Post by paucus

Impresora Delta casera de 25X30 y Calibración

by diegognavarro 		1,725 15 04/27/2018 12:42PM
Last Post by sarindangui

Solo gira en un solo sentido el eje Z ????

by cloxx78 		299 1 04/18/2018 10:54PM
Last Post by cloxx78

Infill Vs. Resistencia

by diter23 		465 7 03/19/2018 08:48AM
Last Post by ldcampana

PRESENTACION

by artesano 		284 1 03/13/2018 08:32AM
Last Post by artesano

EXTRUSOR MK8

by lea.alm.nat 		349 1 03/06/2018 02:48PM
Last Post by lea.alm.nat

Problemas con Extrusor Externo

by SG-1 		309 2 02/26/2018 12:29PM
Last Post by SG-1

Movimiento de impresora fuera de escala

by Taglio 		346 2 02/06/2018 02:54PM
Last Post by diegognavarro

Armado de impresora S-BOX CORE XY Attachments   (Pages: 1 2 3 4)

by maic 		7,100 110 01/29/2018 09:18PM
Last Post by diegognavarro

Corte de aluminio para marco de Prusa I3 custom

by ldcampana 		454 3 01/19/2018 07:27AM
Last Post by ldcampana

Mi home no va bien en mi impresora

by edgar360 		312 2 12/26/2017 04:07PM
Last Post by diegognavarro

Ayuda - Molde Vasos Sustentables! Attachments

by enepece 		384 2 11/11/2017 10:26AM
Last Post by tatubias
Page 1 of 36    Pages: 12345NextLast