first few prints, major issues December 08, 2012 07:16PM |
Registered: 11 years ago Posts: 7 |
Re: first few prints, major issues December 08, 2012 09:01PM |
Registered: 11 years ago Posts: 560 |
Re: first few prints, major issues December 11, 2012 08:56AM |
Registered: 11 years ago Posts: 10 |
Re: first few prints, major issues December 28, 2012 11:10PM |
Registered: 11 years ago Posts: 16 |
Re: first few prints, major issues December 29, 2012 05:22AM |
Registered: 13 years ago Posts: 2,947 |
FFF Settings Calculator | Gcode post processors | Geometric Object Deposition Tool Blog |
Tantillus.org | Mini Printable Lathe | How NOT to install a Pololu driver |
Re: first few prints, major issues December 29, 2012 07:44PM |
Registered: 12 years ago Posts: 115 |
Re: first few prints, major issues December 29, 2012 09:26PM |
Registered: 13 years ago Posts: 2,947 |
FFF Settings Calculator | Gcode post processors | Geometric Object Deposition Tool Blog |
Tantillus.org | Mini Printable Lathe | How NOT to install a Pololu driver |
Re: first few prints, major issues December 30, 2012 06:59AM |
Admin Registered: 17 years ago Posts: 7,879 |
Re: first few prints, major issues December 30, 2012 02:33PM |
Registered: 12 years ago Posts: 115 |
Re: first few prints, major issues December 30, 2012 06:07PM |
Registered: 13 years ago Posts: 2,947 |
FFF Settings Calculator | Gcode post processors | Geometric Object Deposition Tool Blog |
Tantillus.org | Mini Printable Lathe | How NOT to install a Pololu driver |
Re: first few prints, major issues December 31, 2012 03:40AM |
Admin Registered: 17 years ago Posts: 7,879 |
Quote
To get these other results you have to completely abandon your style of printing and adopt a new style of printing.
Re: first few prints, major issues December 31, 2012 04:23AM |
Registered: 13 years ago Posts: 2,947 |
FFF Settings Calculator | Gcode post processors | Geometric Object Deposition Tool Blog |
Tantillus.org | Mini Printable Lathe | How NOT to install a Pololu driver |
Re: first few prints, major issues December 31, 2012 05:58AM |
Admin Registered: 17 years ago Posts: 7,879 |
Quote
Anyway the point I was making in the post above is the width should not be a ratio of the layer height but rather and absolute width with only the max layer height being limited to 66% of the absolute width.
Re: first few prints, major issues December 31, 2012 09:01AM |
Registered: 13 years ago Posts: 2,947 |
FFF Settings Calculator | Gcode post processors | Geometric Object Deposition Tool Blog |
Tantillus.org | Mini Printable Lathe | How NOT to install a Pololu driver |
Re: first few prints, major issues December 31, 2012 05:03PM |
Registered: 12 years ago Posts: 88 |
Re: first few prints, major issues December 31, 2012 07:13PM |
Registered: 12 years ago Posts: 88 |
Re: first few prints, major issues January 01, 2013 05:30PM |
Admin Registered: 17 years ago Posts: 7,879 |
Quote
There is one extra parenthesis in the above. Should the '/6' term be inside the sqrt() ?
Re: first few prints, major issues January 06, 2013 07:24AM |
Registered: 11 years ago Posts: 16 |
Re: first few prints, major issues January 23, 2013 02:35AM |
Registered: 13 years ago Posts: 2,947 |
FFF Settings Calculator | Gcode post processors | Geometric Object Deposition Tool Blog |
Tantillus.org | Mini Printable Lathe | How NOT to install a Pololu driver |
Re: first few prints, major issues January 23, 2013 06:15AM |
Registered: 11 years ago Posts: 251 |
Re: first few prints, major issues January 23, 2013 07:00AM |
Registered: 13 years ago Posts: 2,947 |
FFF Settings Calculator | Gcode post processors | Geometric Object Deposition Tool Blog |
Tantillus.org | Mini Printable Lathe | How NOT to install a Pololu driver |