Request for Simplify3D gcode test

Quote
Treito
Hey the tooltip of this option looks interesting. I wiould give this a try:
[attachment 59308 retraction.png]

I have that enabled aswell. Having inside out Turned on made the print look worse. I think its the ooze that comes out in travel moves that actualy couses blobs and its due to E3Ds huge heating aluminum block.

Kiboplast does not ship to slovenia

Edited 1 time(s). Last edit at 08/03/2015 05:11PM by Darathy.

After turning on this option I have no blobs independent of the filament. Even my oldest one (1,5 year, stored at open air at 77% (!) humidity) works. Okay 3DFilaments.ie I did not test directly but I have now a smooth surface without blobs. But I needed to turn on this otion first, so you will definitely need this. I also enabled coast at end with 1,5mm and I use random start points. And I increased the temperature. All this together hopefully helps, but you should definitely see less blobs.
I should thank you otherwise I would not really have recognized the problem. I hope you did not get it wrong by now.
So as it made here differences you should try all together. I could also send you my settings or even generate a g-ode to see if your problem is somewhere printer related but I do not have any idea why it should so. It is strange why this does not work for you.

Maybe you can get Kiboplast by any kind of distributor or an online-shop or ebay? You may also try Supremery or maybe NuNus even though at the last one there are different experiences. I only tested NuNus ABS. Except for a windings problem I did not have make any real bad experience but the windings were mixed up. Supremery I only tested one spool PLA. These three manufacturer seems to have similar colors. There are slightly differences. At first I thought all would be the same but the properties and behavior of the filaments slightly differs.

---

Slicer: Simplify3D 4.0; sometimes CraftWare 1.14 or Cura 2.7
Delta with Duet-WiFi, FW: 1.20.1RC2; mini-sensor board by dc42 for auto-leveling
Ormerod common modifications: Mini-sensor board by dc42, aluminum X-arm, 0.4 mm nozzle E3D like, 2nd fan, Z stepper nut M5 x 15, Herringbone gears, Z-axis bearing at top, spring loaded extruder with pneumatic fitting, Y belt axis tensioner
Ormerod 2: FW: 1.19-dc42 on Duet-WiFi. own build, modifications: GT2-belts, silicone heat-bed, different motors and so on. Printed parts: bed support, (PSU holder) and Y-feet.
Ormerod 1: FW: 1.15c-dc42 on 1k Duet-Board. Modifications: Aluminium bed-support, (nearly) all parts reprinted in PLA/ ABS, and so on.

but you do not have E3D i guess? I think i'll have to go back to stock ormerod hot end ,just a shame for me to waste 100€ for this ,I have also ordered 0.5mm nozzle for E3D and will see if it may be bit better(less preasure).

No and my new one will only get clones. So have you tried all options together yet?

---

Slicer: Simplify3D 4.0; sometimes CraftWare 1.14 or Cura 2.7
Delta with Duet-WiFi, FW: 1.20.1RC2; mini-sensor board by dc42 for auto-leveling
Ormerod common modifications: Mini-sensor board by dc42, aluminum X-arm, 0.4 mm nozzle E3D like, 2nd fan, Z stepper nut M5 x 15, Herringbone gears, Z-axis bearing at top, spring loaded extruder with pneumatic fitting, Y belt axis tensioner
Ormerod 2: FW: 1.19-dc42 on Duet-WiFi. own build, modifications: GT2-belts, silicone heat-bed, different motors and so on. Printed parts: bed support, (PSU holder) and Y-feet.
Ormerod 1: FW: 1.15c-dc42 on 1k Duet-Board. Modifications: Aluminium bed-support, (nearly) all parts reprinted in PLA/ ABS, and so on.

yes turned evrything on .but no change