Re: newbee to platformio, need initial startup to configure for board only in imports file. December 30, 2022 09:51PM |
Registered: 1 year ago Posts: 28 |
Re: newbee to platformio, need initial startup to configure for board only in imports file. December 31, 2022 12:37AM |
Registered: 7 years ago Posts: 341 |
Re: newbee to platformio, need initial startup to configure for board only in imports file. December 31, 2022 01:31AM |
Admin Registered: 13 years ago Posts: 7,013 |
Re: newbee to platformio, need initial startup to configure for board only in imports file. December 31, 2022 01:34AM |
Admin Registered: 13 years ago Posts: 7,013 |
Re: newbee to platformio, need initial startup to configure for board only in imports file. December 31, 2022 01:49AM |
Admin Registered: 13 years ago Posts: 7,013 |
TMC UART moder set O O O M0 O O O M1 O=O O M2 O O MKS TMC2209, MKS TMC2225, MKS TMC2208 plug in to use UART mode directly
Re: newbee to platformio, need initial startup to configure for board only in imports file. December 31, 2022 01:54AM |
Registered: 1 year ago Posts: 28 |
Quote
[email protected]
YES!!!
"project init command" - I have no idea what that is. Is it a VSCode thing?
I took your ZIP file and unpacked it. I then took the ..\Marlin-2.1.1\Marlin\configuration.h file and modified it (the modified version is attached to my last post). I then opened a shell window, navigated to the directory ...\Marlin-2.1.1 and issued the platformio run -e mks_robin_nano_v3_1 command. No "project init command" involved.
I'm REALLY surprised that the touch screen worked. Usually there is a serial port that is used to communicate between the motherboard and the touch screen. As far as I can tell only the USB port is enabled. What touch screen do you have? How is it connected to the motherboard?
TFT35 that I cut the knob and pot off of so it would fit the existing window in the printers base, The versioi 1.2 board had a 40 pin ribbin cable to connct them, the newer board uses two 20 pin cables on normal header connectors.
"5 point bed leveling" - I don't think that is a Marlin thing. You'll have to read the docs as to what leveling options are available in Marlin.
That is one of the options for g29, but its a build time option, one of at least 6 ways to do it from what I've read.
I have now tried all 3 versions of the jumpers inside the driver sockets, with affecting the TMC COMMUNICATIONS ERROR at boot time. None of the three will run the motors properly. It turns out thaat I have 4 of the TMC2225's, aparently from the old board, and 5 of the TMC2209's that came with the new board kit. Supposedly interchangeable but the error at power up remains, X moves extremely slow but it the right directoin, Y moves fitfully stopping while x moves right. an Z tries to go around 10,000, stalling, and all will now generate a home error, please reset msg. So something is still fubar.
Do you have a bed leveling probe (such as a BLTouch)? Most of the advanced Marlin bed leveling options uses a matrix of probed points. Filling the matrix in manually is a real pain so a bed leveling probe is soon on the upgrade list.
Re: newbee to platformio, need initial startup to configure for board only in imports file. December 31, 2022 02:03AM |
Registered: 1 year ago Posts: 28 |
Quote
Dust
TMC COM error has many causes.
1) power, these drivers need 12/24v before or at same time as logic voltage. So powering the board just over USB will cause this error.
2) board pins are not set correctly
TMC UART moder set O O O M0 O O O M1 O=O O M2 O O MKS TMC2209, MKS TMC2225, MKS TMC2208 plug in to use UART mode directly
unforch its 2 am here, and all sockets are currently set for spi, I'll change them bsack to uart in the morning and report, right now all 5 are "error:low"
Thanks dust, back in the morning.
3) some tmc stepper driver have a jumper to set what pin is used for uart communications. Or the stepper driver uses a different pin than the motherboard is expecting (common issue if using miss matched brands of components)
You should send a M122 to the controller, it will tell you if it is all tmc stepper drivers of just 1.
Re: newbee to platformio, need initial startup to configure for board only in imports file. December 31, 2022 02:31AM |
Registered: 7 years ago Posts: 341 |
Re: newbee to platformio, need initial startup to configure for board only in imports file. December 31, 2022 11:59AM |
Registered: 1 year ago Posts: 28 |
Re: newbee to platformio, need initial startup to configure for board only in imports file. December 31, 2022 01:33PM |
Registered: 7 years ago Posts: 341 |
Re: newbee to platformio, need initial startup to configure for board only in imports file. December 31, 2022 08:53PM |
Registered: 1 year ago Posts: 28 |
Re: newbee to platformio, need initial startup to configure for board only in imports file. January 03, 2023 01:02PM |
Registered: 1 year ago Posts: 28 |
Re: newbee to platformio, need initial startup to configure for board only in imports file. January 03, 2023 01:05PM |
Registered: 1 year ago Posts: 28 |
Re: newbee to platformio, need initial startup to configure for board only in imports file. January 03, 2023 04:43PM |
Admin Registered: 13 years ago Posts: 7,013 |
Re: newbee to platformio, need initial startup to configure for board only in imports file. January 03, 2023 10:09PM |
Registered: 1 year ago Posts: 28 |
Re: newbee to platformio, need initial startup to configure for board only in imports file. January 03, 2023 11:32PM |
Registered: 7 years ago Posts: 341 |
Re: newbee to platformio, need initial startup to configure for board only in imports file. January 04, 2023 06:01AM |
Registered: 1 year ago Posts: 28 |
Re: newbee to platformio, need initial startup to configure for board only in imports file. January 04, 2023 06:17AM |
Registered: 1 year ago Posts: 28 |
Re: newbee to platformio, need initial startup to configure for board only in imports file. January 04, 2023 07:36AM |
Admin Registered: 13 years ago Posts: 7,013 |
Re: newbee to platformio, need initial startup to configure for board only in imports file. January 04, 2023 08:31AM |
Registered: 1 year ago Posts: 28 |
Re: newbee to platformio, need initial startup to configure for board only in imports file. January 04, 2023 03:32PM |
Registered: 1 year ago Posts: 28 |