Hi, recently i finished off a whole spool of filament and then got my self a new spool of the same material by the same manufacturer but different color. when i start to print with this spool i noticed that there were some delamination issues and i tried almost everything i know to fix it. what i did: increased and decreased the retraction length increased and decreased temperature reduced partby yoonus_rox - Reprappers
omfg thank u so much!!! u have no idea how much pain my head has been going through trying to solve this problem.by yoonus_rox - Reprappers
Hi, about a few months ago i took out my 3d printer which i had kept away for a while and started to 3d print with it. everything was fine and it would print well. that is unitl recently when i started having problems with my y axis. whenever i home the y axis it moves the wrong direction by a few mm and stops and when i move the y axis using pronterface it would only move one direction and not tby yoonus_rox - Reprappers
hi everyone, after a lot of trial and error i have finally found what caused the issue. turns out the little ptfe tube that you find in the heat break was missing so if anyone else has any extrusion problems with the hotend be sure to check out if your heat break has the little ptfe tube in it like the one in the file that i have attachedby yoonus_rox - Reprappers
hi, recently i took out my 3d printer which i havent used in a long time and when i started prining with it the filament gets blocked in the hotend. i tried everything the internet has told me and none of th m have fixed the problem. what i did: increasing hotend temperature reduced hotend temperature increase fan speed to max changed the heatsink cooling fan air flow direction twice tighten theby yoonus_rox - Reprappers
hi, recently i took out my 3d printer which i havent used in a long time and when i started prining with it the filament gets blocked in the hotend. i tried everything the internet has told me and none of th m have fixed the problem. what i did: increasing hotend temperature reduced hotend temperature increase fan speed to max changed the heatsink cooling fan air flow direction twice tighten theby yoonus_rox - General
i got myself an mk3 pcb haetbed about last year. recently i decided to use it and so when i was soldering the wire onto the heatbed it was not sticking onto it i tried using a lot of flux on it but it didnt fix it please help!by yoonus_rox - General
i use a creality thermistor so i set it to: 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) is this the correct TEMP_SENSOR_BED type for my creality thermistor??by yoonus_rox - Reprappers
hi thank you for replying. I did as you said and found that my thermistor temperature isn't the same as the room temperature its about 20celcius degrees more than room temp. does this mean i have to change my thermistor or is there a way to fix it?by yoonus_rox - Reprappers
Hi, i recently installed my first heat bed to my 3d printer but unfortunately during the print after heating both the heat bed and the hot end up the print stops and pronterface displays this error message Error:MINTEMP triggered, system stopped! Heater_ID: bed Error: Printer halted. kill() called! Error: Printer halted. kill() called! this hasn't happened before I installed the heatbed iby yoonus_rox - Reprappers
I'm using ramps 1.4 A49AA stepper driver 17hs1352-p4130 stepper motor is it ok if the stepper motor pulley and the idler pully hav different number of teeth and width?by yoonus_rox - Reprappers
will adjusting the current of the drivers reduce heating?by yoonus_rox - Reprappers
hi i recently built my 3d printer and i have the layer shifting problem i kept reading about it but never understood the solution can someone pls help me and explain the solutionby yoonus_rox - Reprappers
hi guys i made this forum but then i found the solution... now i dont know how to delete this forumby yoonus_rox - Reprappers
hi I recently finished building a 3d printer which uses ramps1.4 but my plastic extrusion seems to have a problem. during the first few second of the print the plastic extrudes fine but later it gets jammed in the hot end and doesn't allow the extruder to push the plastic. the bed level is adjusted so that it doesn't block the nozzle. I don't know much about the extrusion multiplier setting butby yoonus_rox - Reprappers
hi i recently finished building a 3d printer which uses ramps1.4 and when i started to print i realized that my z axis moves too much for each layer (about 5mm - 10mm high). I set the the first layer height and other layer heights to 0.4mm the first layer is always fine but the others are not . I use a T8 lead screw and a 17hs1352-p4130 stepper motor for my z axis.by yoonus_rox - Reprappers