Quotecameleon Une petit chose, si je veux un éclairage plus vive, je dois aller vers 1k ohm ou vers 10k ohm ? Vers 1k.by enif - RepRap Groupe d'Utilisateurs Francophone
Tu as probablement mal compris en ce qui concerne la resistance: 1 a 1.4 Ohm c'est la resistance "chauffante" du lit. La resistance a souder sert pour delimiter le courant a travers les leds. Moi j'utilise 2.7kOhm ce qui me donne env. 3mA - assez pour voir, mais sans que ca me derange quand le PWM est en mode "clignotant" - mais n'importe quelle valeur entre 1k et 10k devrait fonctionner. Comby enif - RepRap Groupe d'Utilisateurs Francophone
Quotesiggi60 Führe mal M502 aus. Dann lädt er die Firmwarewerte und alles sollte gut sein. ... und danach am besten noch M500, damit er die Firmwarewerte auch im EEPROM speichert.by enif - Software
Usually, it's the maximum step rate of your controller which is limiting the achievable speed, so a good point to start is this wiki page.by enif - Stepper Motors, Servo Motors, DC Motors
Im Wesentlichen hat er bei den Flachkabelstecker die auf der einen Seite rausragende "Nase" abgeschnitten und dann die Stecker 180 Grad gedreht und wieder eingesteckt... Ich hatte das gleiche Problem auch einmal, da hab ich aber die Stecker nicht "amputiert", sondern die Plastikteile der Sockel auf der Platine mit einem Messer vorsichtig gegen oben abgezogen und dann 180 Grad gedreht wieder überby enif - Elektrik & Elektronik
Watch out, the shape of this type of ship hull is not entirely convex, so if you use OpenScad's convex hull() function, you will be loosing the convex "cavities" in the front part of the hull.by enif - OpenSCAD
Why don't you post a photo where we can see that particular ship's hull. Not all ship hulls are the same, so having an image would help us to understand what you are trying to do.by enif - OpenSCAD
Si jamis ce n'est pas juste le serrage de la poulie sur l'axe du moteur: Est-ce que le probleme disparait en diminuant le parametre d'acceleration pour l'axe Y?by enif - RepRap Groupe d'Utilisateurs Francophone
Did you remove the capacitors from the PCB when measuring them? (They are essentially all connected in parallel, so you cannot measure them individually when soldered on the PCB.) If you did unsolder them, did you then try if the 12V power supply still switches of when connecting it with USB connected? Other question: Are you sure that your power supply is not the problem?by enif - Sanguino(lolu)
Wieviel Retract hast du denn eingestellt? Irgendwie hast du entweder Probleme mit der Kühlung oder du ziehst das geschmolzene Filament zu weit nach oben. Welches Hotend hast du? Kannst du uns Bilder von deinem Hotend zeigen?by enif - Software
There is only one trace marked in the picture, and yes you should cut it with a sharp knife. Could it be that the 1000uF or one the 100uF capacitors became defective?by enif - Sanguino(lolu)
Did you connect the USB before switching on th 12V? (Needed since you removed the 7805.) I see that you added the Schottky diode at the USB input, but from the photo it looks as if you did not cut the trace, so that the diode would be useless. Do you still get the hissing sound when you remove the ATmega1284?by enif - Sanguino(lolu)
No, if your board was working okay before, then I don't think either that it's a faulty PCB. Have you tried removing all stepper drivers, the heatbed and the hotend. Is there still a short? If not, reconnect one by one (always turn off the PS when connecting/disconnecting something) until you find the culprit. The lack of 7805 will definitely not cause a short. If you can post some photos oby enif - Sanguino(lolu)
If the light on your 12V goes out, it means that you probably have a short somwhere, so that the over-current protection of the PS switches the PS off. Have you measured the resistance between 12V and GND on the Sanguinololu board? I have had 2 Sanguinololu boards which were not well etched and had some copper traces shorting between 12V and GND. Once I found them and cut them with a sharp knby enif - Sanguino(lolu)
QuoteEbdac Do you mean this pin? There is nothing there. Yes, that one too should have 5V. But it's much easier to access the "5V" pin on the very lower left corner in your picture, or also the "5V" pin on the EXT header, 2 positions to the left of your arrow. QuoteEbdac Now something strange happened, when I was trying to check the voltage on the pins the board came to live when the switch iby enif - Sanguino(lolu)
From your description I assumed the problem is with the 5V, so I don't see what the MOSFETs have to do with it. Do you have 5V on the 5V pin when only 12V input is connected?by enif - Sanguino(lolu)
Das sieht doch irgendwie so aus, als ob dein Heizelement zwar gerade knapp stark genug ist, um das Hotend im Stillstand aufzuheizen, aber nicht stark genug, um beim Drucken das einkommende Filament zu schmelzen. (8 Minuten zum Aufheizen das Hotends sind ja eine "Ewigkeit", bei mir dauert es weniger als eine Minute.) Wieviel Strom zieht denn dein Heizelement, oder (einfacher zu messen) welchen Wby enif - Software
Probably it's just the LM7805 regulator that needs to be replaced. Note that the Sanguinololu is known to have issues related to the 5V input when both USB and 12V are connected, see here. I have added 2 Schottky diodes to resolve the problem, as explained here.by enif - Sanguino(lolu)
Moi j'imprime sur une plaque de verre (en effet c'est un mirroir) que je nettoie d'abord avec de l'acetone et pour finir avec du jus de citron doublement concentre (ou recemment avec de l'acide citrique dissolu dans up peu d'eau destillee). Ca tient bien avec ABS et PLA, et en refroidissant --autour de 40 degres-- les objets imprimes se detachent soi-memes, des fois meme avec un "claque" qui lesby enif - RepRap Groupe d'Utilisateurs Francophone
As-tu deja fais une recherche sur thingiverse.com pour des mot-clefs comme "X-axis", "X-carriage" ou "X-ends"?by enif - RepRap Groupe d'Utilisateurs Francophone
Est-ce que les 2 moteurs sont identiques? Si tu mesures la resistance des bobines est-ce que ca donne les meme valeurs? Par defaut sur le RAMPS les deux moteurs Z sont cables en parallele, ce qui ne fonctionne que lorsque les impedances sont les memes, autrement, le moteur avec l'impedance plus bas recoit le gros du courant. De toute facon, si tes moteurs ont une basse impedance (ce qui est leby enif - RepRap Groupe d'Utilisateurs Francophone
Das Foto der Hülse ist leider nicht so klar. Hast du so etwas im Sinn? Wenn ja, dann hab ich das so gemacht: module huelse( hb = 1.18, // Höhe Boden db = 7.95, // Durchmesser Boden aussen hh = 4.9, // Höhe Hülse da = 4.9, // Durchmesser Hülse aussen fa = 3.9, // Abgeflachter Durchmesser aussen di = 3.4, // Durchmesser Hülse innen fi = 2.4, // Abgeflachter Durchmesserby enif - Software
In deinem Schaltplan hängt das gemeinsame Plus am "5V" Pin des Ramps. Dieser ist jedoch m.E. ein "Misnomer", da er nicht an 5V liegt, sondern einfach ans Plus der Servo-Ausgänge gelegt ist, d.h. er ist im Normalfall nicht verbunden. Erst wenn man einen Jumper zum benachbarten "VCC"-Pin legt, kommen die 5V zu den Servos. Deshalb würde ich vermuten, dass das gemeinsame Plus mit dem VCC-Pin undby enif - Elektrik & Elektronik
Einer der Anschlüsse der grossen Spule (roter Kreis) sieht auf deinem Foto etwas komisch aus. Kontrollier mal, ob sich da evtl. eine kalte Lötstelle gelöst haben könnte:by enif - Elektrik & Elektronik
Öffne und schau mal, ob die eingelötete 6.3A Sicherung durchgebrannt ist:by enif - Elektrik & Elektronik
Si ta "carte Arduino" est de type Mega2560/RAMPS, il y a derriere les fusibles et la diode D2 une prise pour 12V ou tu peux connecter un ventilateur qui tourne constamment. Souvant le 2-pin header n'est pas installe, donc il faudrait d'abord l'ajouter (ce qui est mieux que souder les fils directement sur la carte). Puisque ca tourne toujourse, il n'est pas necessaire de modifier le firmware.by enif - RepRap Groupe d'Utilisateurs Francophone
As-tu deja baisse les valeurs de vitesse et d'acceleration dans Marlin? Celles pour X et Y me semblent assez hautes port les premiers tests, il vaut mieux de commencer bas et d'augmenter au fur et a mesure une fois que tout le reste fonctionne bien.by enif - RepRap Groupe d'Utilisateurs Francophone
Das Problem kenne ich auch, bei mir war es aber die USB-Verbindung vom Sanguinololu die abbrach, wann immer ich das Licht (Leuchtstoffröhre) im Raum löschte. Hab mit allen möglichen Filtern probiert, ohne Erfolg. Schliesslich habe ich die Leuchtstoffröhre durch LED Leuchten ersetzt und seither ist das Problem nicht mehr aufgetreten.by enif - Elektrik & Elektronik
Quotejamesd256 Would it not be the case that the affect of a lower resistance would simply be faster increases in temperature when the heater was on? In other words, would it be necessary to change the duty cycle settings? No, I assume that a smaller resistance should work fine (even better) without a reduced duty cycle - as long as the resistor survives the higher wattage at the start-up. I wby enif - RAMPS Electronics