Guys, I have an object to print, it's printed but why on the right hand side edge, it was not printed completely, it's missing about 3mm to right ? What's wrong here ? Thanksby bianchi - Reprappers
Guys, How can I pause printing when my filament is finished and I'm sleeping ? Any ideas ? Thanksby bianchi - Reprappers
Guys, I tried to print something hanging from Z axis and some of them are not sticking each other properly, and I fixed it with epoxy glue, Any solution for it ? It's some kind a long tube and I print it horizontally because if I print vertically the bottom is very narrow to stick... Any clues ? Thanksby bianchi - Reprappers
Guys, How can I put support for printing non flat object to Z axis ? Thanksby bianchi - Reprappers
Guys, Is it strong enough if I print a bike show with PLA ? Thanksby bianchi - Reprappers
Can I spread the sugar on galvalized bed ?by bianchi - Australia, Melbourne RUG
I'm using Scotch 3M 2093.....I can't find 2090 here..... It's sticking like above example..... I reduce it by putting cooking oil on it...by bianchi - Reprappers
Is it good if I use acrylic sheet for my heat bed ? Like this one : Acrylic sheetby bianchi - Reprappers
Do you still need it ? What do you want to print exactly ?by bianchi - Australia, Perth RepRap User Group
I used 2093 but it's sticking very well.....and I need to scrap the bottom part of the printed items... Any ideas ?by bianchi - Australia, Melbourne RUG
After scrapping with sand paper...by bianchi - Reprappers
Probable I soak it with kerosene to clean the bottom part ? what do you reckon ?by bianchi - Reprappers
I have wipe it with alcohol before printing and using 30 degree heat on the bed but it's still sticking very well... Please have a look: Now I need to scrap it with sand paper to clean it..... Any ideas to make it better.....? may be more alcohol ? Thanksby bianchi - Reprappers
Scotch 2093EL blue masking tape...by bianchi - Reprappers
I've reduced to 30 but it's still sticking very well...any clues ?by bianchi - Reprappers
Guys, I tried printing with Scotch 3M blue tape and PLA filament, but by the time it's finished, I can not release the tapi from printed object, I need to scrap it with sand paper... Any ideas ? Thanksby bianchi - Reprappers
Guys, Why can't I reach 230 C on melzi board ? I stuck at 205 C and difficult to go up again on my extruder .. Thanksby bianchi - Reprappers
Can I use this one as a filler ? Diggers 250g Fibreglass Resinby bianchi - Reprappers
Is a car body filler a paste or sprayable liquid?by bianchi - Reprappers
Anybody knows ? I tried to print with it, why it's not sticking between layer, any solutions ? thanksby bianchi - Reprappers
Guys, I tried to print with carbon PLA, but strangely it's not sticking between layer.....what should I do to fix it ? thanksby bianchi - Reprappers
You can upload *.hex file directly to the chip....what's your board name ? please have a look on your PCB and what's the chip type...if it's marlin, it could be atmega1284P... That's the one I use....by bianchi - Reprappers
Guys, Is it possible for me using dual colors extruder with melzi board ? Thanksby bianchi - Reprappers
Is your chip Atmega1284P ? what's your board name ? If you need to flash it, you're going to need a programmer like USBASP for Atmega1284P, avrdude, some cables for connecting to its SPI port....by bianchi - Reprappers
Guys, Can I paint PLA with acrylic clear paint ? With this one : White Knight 310g Crystal Clear Acrylic Clear Gloss Thanksby bianchi - Reprappers
Do you mean FDM is "Fused deposition modelling (FDM)" ? And may be for a simple test I make tube, and then give a stress with my weight plates 100kg and see what happen ? what's the thickness of the tube normally ? there's a possibility that I make a frame / structure inside the tube, some kind a bone inside the tube for supporting the strength of it.... Thanks for your insight...by bianchi - Developers
It's in cm of course... Do you reckon delta 30 x 18 would be good enough ? I want to print a tube ( pipe ) for bicycle frame....is it possible with 20x20x20 printer ? then join all of them together ? Thanksby bianchi - Developers
Guys does anyone of you build a large reprap? Any experiences I want to build 150x100x100 Thxby bianchi - Developers